Search results

Oh man where to start. I've made a lot of wooden bodies over the years with just a drill, handsaw, some sandpaper, and an hour or two of free time. No machine shop required 1. Buy dowels instead of square blanks of wood. This will save a lot of time. You may not be able to buy the exact outer...

I had some very good luck with this on my Impcognito. It is the thickest 316 stainless steel gauge. I use it in wattage but you really gotta crank it up to get a good glow. Might be worth trying something similar in the stempod. https://postlmg.cc/MvVjbMG7

I used these off my old QQ. ABV was the absolute most even out of all of the materials I've used. Downside was the lower heat up and the stempod ran way hotter.

Very interesting, I'd like to mess around with one of those. I do think a 510 sized chamber would be too small, off the shelf anyway. You could probably drill it out a bit.

My local vape shop had this Vandy Vape Mesh RDA on clearance for $10 so I picked it up for some fuckering about. Here's what I ended up with. This has a heatsink included here but it is SMALL. About the height of an impcognito with the heatsink. The diamer is bigger at 24mm. It came with...

That's a realeaux rx75. Might be difficult to find nowadays. @Pipes posted a 21700 near the top of this page.

Oh man I've been barking up that tree for a while. Here's all the single 18650s I've owned. https://postimg.cc/GT04TSGy https://postimg.cc/DmYrwh3y https://postimg.cc/PLkznMsW https://postimg.cc/w7jMM934 This one has custom firmwares available

Only one I really know of is the Paramour There's this also but I bet it isn't cheap. https://strangersmods.com/side-by-side/21700/ Movkin disguiser is double 18650 and very cheap if you can still find it. Found this also...

Hope I can post my project here as well. Got this Noxus RDA with an interesting swivel/ magnet lid and instantly wanted to mod it for vaping herb. I made the wood bowl but I'm having trouble getting it to sit properly. It fit in there very tight, but I found that the wood shrinks when heated...

Honestly you could have a stem today if you're willing to put some work into it. You could run out and buy some fine grit sandpaper and sand the bowl down a bit until it fits. Should take 15-20 minutes. I've done it once before. Wear a face mask and eye protection, do it outside. This is...

It's a proprietary size so your options are limited. You could write the owner on Instagram to see if he has any left over. I bought an Enano stem on PoTV that fit well. https://www.planetofthevapes.com/products/e-nano-adjustable-gong-stem

Check out this wood body I made for the Gen 2

Check out the PenPal lathe if you're low on space. It's small but good quality. It's meant for making pen bodies, so making stems on it should be pretty easy.

Made a body that takes Solo stems

That o-ring has always been a mystery to me. I have two bodies I bought new from Dave. Sometimes my stems fit easily, sometimes they get stuck in there after a session, sometimes it's just right. I thinks it's just the nature of having a wooden vape since wood contracts and expands constantly...

New imp coil. This was fun to make. The heater is much closer to the herb and works well at low wattages

Put these monster 20 gauge 316SS coils on the Impcognito. Stock coil on top for reference. Works so good it's crazy. Much easier to avoid coil glow. It does heat up the device more quickly though.

Got this new mod today. Not sure how I feel about it yet.

I really appreciate you checking that for me! I love 510 vapes and I'm up for the challenge. It took me almost a full year to dial in my Imp the way I like it but it was worth it.

Yeah I've been reading it all day. I was just wondering if it's a true 25mm since I could see a bit of a gap on the 25mm mod they bundle it with. My mod fits 24.5mm and I'd rather not have to buy a new one. I've been seeing mixed reviews for sure but I'm getting it for so cheap I don't really...