Search results

Well i found something close to what i had in mind but i cant find a enail compatible version....i think the original glass artist was C2 custom glass the "daisy" style quarts nail......basically i like the open cup shape "i love bangers but the current designs are lacking....coil needs to...

I dont think you conctrate has to make contact with the ti to alter the taste. It jus has to be hot and in th3 air path. Ai have a Controll box jus need to find a nail . Not reall worried about ati being in the pathway just near too close to coil and getting hot

But a bit of the flavor is impededed by the Hot ti of the liger....anybody have any recomendation for a nail that all qurtz or ceramic....thats not a kings moat stlye (( the halo))

Hasnt shipped yet.....have they

I THINK youre mistaken about the ability of Ti shell to protect the banger from the expansion of the coil. Or am I confused and Ti doesnt have a much greater thermal expansion rate than quartz....i have had two turtle bangers break in the last month first from leaving the coil and shell on as...

CAUTION!!! THE TURTLE BANGERS ARE NOT for anyone who is not A)Experienced enail user B)Experienced and/or well informed in using an enail with quartz nail..... The Ti shell is amazing as far as the Ti's heat dispersion helping make up for Quartz shortcomings in that aspect..... HOWEVER THE...

But in relation to this the topic of this thread . What are peoples experience and opinions as to the best kinda of rig to use to dab with an enail configuration. Why? What specific qualities are you looking for in the perfect rig for enail use. Is there a difference between the best rig for a...

So this thread seems so be incomplete in considering all aspects of a "Next Generation Enail setup"...Ive read through the information and discussion already posted in this thread and had a thought occur to me...we've discussed the Temperature controller unit ,the type and size of heating...

Oh the coils ability to heat the nail is not what i find issue with. It the entire thermodynamic form and function as a nail with out regard to material or how well a enail coil heat it.... the flaw is in the vaporization suface being a ring with the air path going down through in the middle...

The set temperature seem fine below 700f around there the coil seems to start to fall to reach the set temp...on average its will stop 75f short of set temperature @Gonzo_da_wind does the display say that your coil is resting at the set temperature or below it? If it says the actual...

Even were Josh were to offer a full refund i would blink twice before politely refusing......I will admit to buying this e/nail rather quickly without thoroughly doing my homework on it. But I had done my homework on just about all the nail/coil setups and had found most stuck to the old basic...

So Josh actually was aware of these issues... or the design flaw and has already begun implicating a rather simple (( but clever in its simplicity)) improvement/fix that changes almost nothing. Hes slightly shortened the larger cup side to the insert so that has clearance to thread in above...

Almost.....but its not a matter of doing 1 dab and havi g to wait before next...its cooling almost instantly mid dab.... I think is another possible conttibuting factor...if i draw to hard while the carb cap is in place then the vacuum causes the insert to sucked off the bottom of the Ti banger...

y I did the adjust til right the set and leave alone....but as if its own accord itll start burning dabs so i lower by a lil and instantly its too cool and my dabs begin to pool..but if raise the temp at all it takes a moment but itll get to burning again

Yes this was what I initially tried....i cant explqin it but ass i go up in temperature there seems to be a point where it shifts from too cold to too hot but that margin between seems razor ....there has to be some factor im not considering...what seems to be to be the complicating component...

Well it seems to have a difficult time getting the quartz insert to the liger banger ((are you familiar with the design)) hot enough to dab ....but as i raise the coil temperature....the dish quickly abd seemingly withouyt a mean way too hot... i tried just giving the heat time to distribute...

Ok so do you have any suggestion on how to adjust my 200rdk to heat my Ti banger with quartz insert.?

ANY One wondering if the Ti nail is really necesarry/ most optimal setup for this device.... What im talking about is that I personally perfer a quartz or Ceramic vaporization surface to Ti....and while quartz maybe out of reach for this device underneath the nail is a ceramic rod that is the...

Hey does anyone have the 200 rdk and the 20mm Liger V2 and happens to know the temp coefficient for the 20mm Liger v2 with quartz insert....i dont have a IR Thermometer or thermocouple

@mrbonsai420 How does your Storm cap fit on your Liger V2? Does it fit better on the Liger V1? It looks like the V2, when compared with V1 is: more modular. can be bought in a bigger size (20mm). and can fit on a 45* rig. Am I missing some other attribute that raises the V2 above the V1? The...