Search results

Could you show us how it loads and cleans? By the way, good review.

I had a similar experience on a different site and it turned out to be the browser I was using (Firefox).

I hope I am not being too obvious here but there are only two things you would need to do. Be able to take the unit apart and to be able to find a suitable battery replacement. You might need to MacGyver a connection but I would think anyone contemplating this would not have trouble imprevising...

Ah, now that actually makes sense. The rule itself does not engender that thus is open to interpretation. Thanks for clearing that up. Sorry about the grief.

I was taking a look at the rules of this Forum and to my surprise I found this: "Forum Policies" "If you have a question or comment regarding material safety, post it in General Discussion. Do not post it in a model thread." So if I have a question or comment regarding material safety of a...

I think the use of the word "panicking" was a bit over the top. "Concerned" would have been a better choice. And as previously observed, I should be able to post what I wish as long as I stay within the guide lines of this Forum. Thank you for your review.

I bought a Da Buddha for one of my sons awhile back. The whip that came with it smelled weird, from the manufacturing process no doubt. It was almost foul. But it did not take long for that smell to go away. Maybe that is the problem here I do not know. The fact that it gets worse as it gets...

Cool, I am glad someone finally get that. All that is really necessary is that there is no possible chance it will off gas anything harmful, and the temperature stays relatively constant; I am there.

It was to show that the material would melt. The point of concern is where that plate and the hot part of the mica heater assembly come into close quarters, at the center underneath the mica heater assembly. My original post said that the bottom of the mica heater assembly gets hot enough to...

When I posted I said I could provide pictures if anyone wanted to see.

So, it is safe to have plastic exposed to temperatures that could at least cause off gassing in the air path? Yes you are probably right about the speculation. But I would also speculate that if I was hit by a car I would suffer some sort of injury. The Solo has plastic in the air path...

Jens: Some units smell. This is mainly to do with a small circuit board under the bowl assembly. There is flux on it that was not cleaned away when it was assembled. Denatured alcohol and a half dozen or so Q-tips should take care of that. I would not use the Solo as your main/party vape...

I do not think so. The block surrounding the bowl/heater probably is (bottom too). Under that block is a plastic plate that form fits around the bottom of the mica one you are talking about. The clearance between the two can not be more than 1/8" (sorry metric folks). Have you taken yours...

Do you use your Solo for multiple 12 minute sessions? Does the whole unit heat up and feel warm in your hand? You may be partially melting the plastic plate at the bottom of the bowl assembly (assuming you have one like the two of mine). There is not much room between it and the block that...

I feel I must apologize to those who read my post and cleaned their bowl block and found the Solo still smelled. I was wrong about the air path being restricted to that block. The hole for the wires bringing power to the bowl is big enough to allow air to pass through. The block is not the...

The Smell Issue (IMHO): I think that you all will eventually find out, as I did, that the bulk of the smell from the Solos that smell is coming from that block that houses the bowl. The "electronics" smell is similar to flux which is used during the soldering process to prevent corrosion of...

I have been pondering this smell issue, as I have noticed it myself thanks to my warranty replacement ss solo. I have been looking at the pictures Vaplexus posted (+much rep), and it looks like the only place that smell could be coming from is from the wires to the heater. Vaplexus you had it...

I have approached a glass blower I have done business with before to see if he would interested in making a custom bat with a recessed area in the bowl to hold a screen. What would the best place for the recess? How would I describe how much restriction the draw should have? What other...

I received my Extreme a few days ago from GotVape, even though UPS made me pick it up. It was a v3, according to the Vaporpedia page, as noted by the display temperature able to be set at 260 degrees C. This was my first vape and I love it. I will never bong again. A pinch, and I do mean a...

Which would be best (taste, components (whip composition, heater ...) durability, ease of use, vapor density, ...) the Da Buddha or the Vaporwarez 4g?