Search results

Pax is tha word.. It's my e cigar...it fill it full up, till it bursts then place a rectangular screen on top( cut to 80% of oven size) close the lid and on low it vapes so long before I go to high to nail it all. I also use tobacco herb sandwich lots to save herb, making it more like the...

Right tried the party mode roll... I'm lol now. Found that full ovens are best long runners, most clouds and taste on low.. I run it low till its out then medium till taste turns abv... Then high till its gone. I modded it by simply adding restriction to mp tube, bit of cotton squeezed in and...

I brought out my mflb which was in retirement and I modded a tube to restrict draw rate, made it so easy to use. Getting huge rips, coughing too... That AA bat keeps giving and it's not hard to steal quick hits in public. Came with me to movies.. Along with pax look at that thread for more on...

Merry Christmas y'all. I see about the battery needing soldered then and also see batt life issues and there I agree it's short. I seem to get more if I charge it and remove it within ten mins of getting green light. Will look at pictures and buy a Nr 2 pax to hit whilst Nr 1 pax charges. Then...

Pull the tube out of mouthpiece look through it. I see a circle of gummy stuff there, blowing dislodges the chunks which are what stops this thing by offering no electric contact. I think that it only contacts from the top of vapor tube, the rim only. That's evidenced by reports that blowing up...

Fill her up, put it on low, start there. Will taste good. Make sure screen is lifted bit by the air tube hole. Let it warm up. I hold finger over mp to not let vapor escape. Start slow hold in for as long as you can. No vapor output on exhale, three of these will make it a merry moment. To get...

Before I get onto pax, remade the convective vape coil ended up at 3.3ohm. Works good, need to make mouth piece now. Rest of this can be followed on the DIY thread where it belongs. Sorry y'all for tracking off.. It's not happening again. Back to pax.... Just finished dinner and pax is now a...

Will do, thanks. Kids hurt makes me cringe. What a crazy world we inhabit. Such sadness such waste. Took pax for a drive today, drum tobacco thins out fast in pax, but there's lots left after taste was gone, no vapor output on exhale... Was good for topping up during kids Chrissy show.. I was...

How about buying an oven door and modding that to have a built in light spring to gently push herbs to oven screen. As it vapes it shrinks no. The slight constant pressure would compact all and allow better heat conduction no? Will ploom sell me spares I live in Australia and ploom only sells to...

I like simplicity, t1 truly is that, no denying it vapes good, coil is ok at 2 ohm, it's the battery setup that worries. I found longer air path allows lower voltage, and helps put pure heat in herbs. No solder used only ceramic and its insulation that really allows low voltage. I like lifepo4...

It's not built right in the electrics, I just got mine, looked at it and it not as good in the control section... Also convection needs long air path over heater coil, also very slow draw til it vapes. Man those batts too small to deliver. Needs better coil tech they know it that's why they sell...

It works but less visible vapor, tobacco taste gone sooo fast, you get best nicotine effect tho, out rips a cig in effects department... All on low, it's slow but gets few good effective doses of nic. Weed is best performer... More visible vape and positively better effect than smoking.. Go...

Full oven on low heat... Big blu cloud... Taste awesome ... I use small round jar... 2x one for abv. I stir at traffic lights. Dump abv straight into container. Dump from container new full load worth. Done at lights. I use dry tobacco or green. Crumbled up it pours like water. Never green and...

Make sure it's clean if it is then get a sharp knife or something metal to bridge the gap between inner tube and outer, join em together electrically, if it goes to heat mode then the mouth piece is dirty inside. Every one cleans outside, that joins to spring and rubs so cannot cause big issue...

How do I add a picture to this post... Help... I used electric tape on oven door to make a flip door so it hangs on and not spills its load.. Just in case see. I noticed I can pop it open as I walk and empty and refill with out stopping. Good for car rides.. Also notice how it makes less vapor...

Pax-solo comparisons... ( love em both): 1. Taste... Solo wins definite... It just tasted better for longer on solo.. 2. Preload... Pax wins here, the battery covers of mflb works on solo stem... Can be done 3. Load bowl/oven... Solo wins its quick and exact. Just put tube in to pre chopped...

All too true, that's the spot to clean, seems it needs to complete a circuit ... I played with a magnet and no mouth piece it stays on in temp change mode. I then put magnet near top of lights and it goes off... Shut down like mp is retracted.. See magnet in mp, silver rectangle.. I thus see no...

Been reading up all posts love all the ideas, just got my pax in Au! What a marathon it was and it costed me too. She better be what I expect. Love my mflb made a big batt for it and it lasts and lasts... First thing I thought after reading all posts is how hard is it to open up pax and see its...