Search results

With ya there, Lady. Since my first Air came with a straight Solo stem (until the shorter ones were made?) I'm thinking Arizer doesn't see a problem there either....... Normally I like the longer Solo stems on Solo. If I'm dealing with the smaller Air format, small stems seem more 'right' to...

Yer welcome. I know that one, I once survived a field assignment in a strange land with local weed and a single glass downstem one of the other guys had the presence of mind to bring ('hey, it's just a glass tube of some kind they asked me to bring to the job site....'). We poked a hole in...

I'm with you, vapes are tools. There value is largely in making vapor. If you're looking for some similar but jaw dropping vapor production, consider the Imag+. At least as fast at the Pro (although I've never raced one against the other), hugely powerful (relatively) when it comes to making...

Mine works just fine in several 14mm connectors. The ring at the top of the mid section (where it seals) is 14.4mm on the VM I just measured. From the looks of it that downstem should work fine, provided it mates with the WT. OF

Card's optional, but if you go that way be sure the wife doesn't find it........she's very unlikely to understand. Of the many ways I can see that coming out most are worth avoiding I think....... Don't be too hard on yourself for not calling Joe earlier, after all you were younger then? OF

Great! I'm sure you won't be sorry. Remember to write yourself a nice thank you note for the BD gift. Not that you don't deserve it, of course, but........ OF

Thanks for the post, I'm obviously still not getting my point across. If, as I believe, the screens are made and installed exactly as intended that is not a fault. You can't say "an ill fitting screen" being a fault is a fact if the "ill fitting" is opinion. To the engineers and inspectors it...

Cool. I guess I didn't make myself clear enough. I see no 'defect' nor justification for "Quality control seems a nonsense when units are going out the door in that condition" since I think it's designed to be built like that. Basically just like is done in Imap+. Are you suggesting they too...

As you say, others have posted about the lower screen being permanent. Some have removed it by fully disassembling the unit and pushing it out from below with a needle, a far cry from " its not difficult". This is an air inlet, no vapor in theory, it should not foul. The same locations in...

While I don't have that one, I do have several similar power banks. They all work just fine for that use, I would expect that one to as well. FWIW a couple of mine have solar panels, not all that useful perhaps, but fun. No, that's not what I said. That unit had problems. And apparently...

Or George Bush....... OF

Bummer. A suggestion, next time hook it out rather than pry? I took a safety pin, heated the tip to glowing with a torch type lighter, then tapped it with the back of a pair of pliers to make a short right angle hook on the end. You can bend it cold, but it's much easier when glowing red and...

That's probably the deal I got in on for my backup ESV. They were 'open box' and mine was very old (middle of the first 100), defective, had the top slider 'all the way up' and the battery stone dead. IMO it was a 'problem unit' VN replaced the easy way and never returned. Joe put it right...

It's definitely easier to do some stems than others. If you take a careful look at the bottom of the bowl, where the tube walls and floor plate meet, you'll notice some taper at the bottom? That is, the diameter of the tube wall of the bowl is bigger at the top than the bottom. This will make...

Glad you got life back in the beast. Neat for sure. Thanks for the good word. To your question, no there's nothing mechanical with the connection (past electrical contact), try it and see. Plug the connector in (but not powered/connected to the computer), ESV still works just fine. You...

No, although some guys use them for that. The primary idea is to add more thermal mass to make vapor. This is a conduction vape. The walls are ceramic and glass, poor conductors. As soon as you start drawing cold air in to take a hit, herb in the center of the mass (away from the walls)...

One of the great strengths of Solo/Air. It does very well on a fraction of a normal load. Another handy feature, not all that common, is the ability to pause a session and pick it up again later. You get as much vapor as you want at a time, not what the vape has in mind. OF

Yes. Sounds like a classic battery issue. Enough battery power to keep it going in standby but as soon as you call for lots of power to make heat it poops out. Given the batteries you have are known weak, I suggest replacing them with at least one new one before going further. FWIW, while...

Love it! A bit of 'inside vape humor' a tiny fraction of mankind can appreciate.......and I'm in that fraction.... Then again, you know it's not the GH thread, you can order a VM and get it this year........ Thanks, that's made my day. Maybe even the weekend? OF

Understood. Note I said 'soften' not 'melt'. If you can soften the plastic (so it's not trying to spring open again) you can hook the cotton part with a bent pin or needle and pull it out. Likewise, poking a needle down though the top and into the plastic tube should allow you to level the...