Search results

That cord can take some fiddling. Once you have the "curl" sitting under the slider it works OK. But does need some adjusting when re-inserting. I did make a video demonstrating this point. Pipes

Hey Jam, your gonna run out of room in your signature soon...:lol:

I know I'm bad for DIY but here's what I use. I like keeping them in pairs without mix up. Also, the way my pouch is set up I pull the pieces out via the top and like to be able to grab everything that way. Nibble up are charged and nipple down need charging. I just rolled them up in a piece...

LOL, I tried it on my thumb but it kept coming off. Maybe needed to be cleaner. Actually, I prefer the soft side as when I was using the rough side the dang thing would stick inside the soft sleeve in the pouch..And turned it on on me once before I got wise to it. A dab of crazy glue on the...

I have one but added another one to my order because to make it work you need to cut down the poker part. I did not want to sacrifice it for an experiment. My thought is to cut it down and thin it out. Could just cut it off but always have that option. Since the UFO piece is on the bottom the...

Wonder how a Dart mid section with the stick shortened and thinned a bit would work. Could use it to start the dump out process as well. Just a thought..... Pipes This one: http://thermovape.com/collections/all/products/theremovape-revolution-dart-loader $9.99

That's a drag. Was helping with the diffusion of the UFO the moisture would last for a least one round? Would making the hole bigger in the smoothflow, ruin the moisture affect? Rendering it useless for the designed purpose? I did read that the UFO can melt Delrin in the tube. I did check my...

I have just been trying this with the long Delrin and there is definitely a difference. Using the SV EVO and it heats and the draw feels different somehow. A little tighter feel to it and the hiss sound is also a little different. I'm thinking the air flow is somehow effected without the top...

That's my understanding as well. The reason, as far as I know, the UFO mouth piece will not fit the T1 cap or flow adapters is the UFO is in the way. My question is. If you remove the UFO tip, can the UFO fit into the bottom of the adapter and put the high temperature PTFE tip into the top of...

Yes the cream coloured PTFE which is an option with the UFO is the only one for that kind of direct heat. Pipes

I have posted this before but nothing wrong with a refresh. For a quick cheap (like me) midterm solution I picked these up at the dollar store. Work fine for me and I remove nightly for the PA time of day. Usually can use over again once or twice. I started liking the rough side first but as...

Yes it will, so that's way : Was thinking about a Smooth Flow for a while anyway, so thew in a proper month piece at the same time. Pipes

You just pushed me off the fence with that discount Tim.. Pulled the trigger on the UFO/w PTFE and the PureFlow. I'm such a sucker.....But I'm sure I'll be a happy camper. Thanks, Pipes

It does get hot up there. Like over 350 degrees. I wouldn't go for the aluminium as it will burn your lips in this application. (More for e-cig I think) Ideally a UFO in the Smooth flow with PTFE month piece sounds good. Just not sure if the UFO will fit as I do not have a Smooth Flow. Pipes

Is it possible to use the UFO on the Smooth Flow.? Would be an expensive option though if possible.

Not really a fair comparison as I would have to order 4 for $20 + around another 20 but last time from Amazon for 4 it ended up about the same. So that been the case I'd prefer to give my money to the TV folks. However, it's a free country and thanks to this forum and you I found some cheaper...

I just went through the motions and not too too bad. 28 + 18.50 shipping + 15% tax + brokerage = around $60. For me that is not that bad. The first run in with batteries and Amazon was for 4 so most of the cost was not the batteries. At least here it's only double. Thanks Ftvo Think I'll pull...

Cool, reminds me of a mod I did on my VG Bat. I used some material from a MagLite holder. Same stuff I see on the back of the poach in the picture above. It melts together nicely with a torch lighter but have to be quick. Just wrap some around and cut the size and heat it and crimp together...

Yep, that's what I understand from what I have read as well and if you order that UFO get the high heat PTFE (cream one). I was going to try as well and use some thick medical tubing to keep from burning myself. (at least not too badly) Something to try tonight....

Glad I could help, have done it myself. A quick wipe and blow throw cleans it for the most part. When it does clog, some ISO on a paper towel will unclog without having to remove it. Although that's not a big deal neither. Pipes