Search results

11.11g

303

I think they meant 100 clicks before the battery needs recharging lol

There's a thread for the ddave ssv dbv and lsv mod here altho most of the pics are gone now unfortunately http://fuckcombustion.com/threads/ddave-mod-for-ssv-dbv-lsv.19835/

Denture cleaning tabs like steradent will fizz up and eat through the gunk in the hard to reach places .... and rinse out afters

Hard to say from the angle of the pic but I think it's a little low Here's their video on heater cover position for reference

Have you checked the top hat or stem screen? I find the performance drops off as the dust n stuff builds up, in and above the screen.

I think it's been bruised by being manhandled too much during the dry process and probably sold on while it was still too wet.

The heat from the ceramic soldering iron element is more localised than I was hoping so I don't think it's up to the job of heating air or balls without a big heatsink to spread the heat. I tried a few configurations with an 18mm Claisen, with and without balls in there but had to go up to...

The Bud Eater is @blokenoname 's brilliant idea from the bottom of this page in the Misty Log thread and carried over the page for pics of inside http://fuckcombustion.com/threads/the-misty-log-diy-wooden-log-vaporizer.26757/page-30 My first build I used the female socket connectors from these...

Couple of updates I built a female Whippi3 :whip:with an 18mm female adapter from the link above, for comparison :science: Using another 1.3ohm 24AWG SS coil wrapped to 8mm this time as the female whip adapters are a little wider and a lot shorter than the males, which only needs about 4.0V...

PID control of the heater, like the Aromed, is another option but that introduces more parts to wire up and a sensor that needs to go in there somewhere (without messing up the airpath). Some PID controllers have a 12V line for us to use or repurposing a 24V soldering iron doesn't look too...

He he he Chipmunk sesh anyone?

Ooooh I've got a few of them :cool: I tried a 1.3ohm 24gauge SS 6mm coil with 3mm glass beads and a couple of Arizer dome screens on the end to hold it all in the whip adapter, like a G43. Which works well at about 13W on a boxmod or 4.9V on the PSU. Great flavour and production like the...

Inspired by recent events in the Misty Log thread, from the bottom of the page here http://fuckcombustion.com/threads/the-misty-log-diy-wooden-log-vaporizer.26757/page-30 I drilled some holes in a male 18mm elbow whip adapter like these https://ebay.us/lCKaHK , put a 6mm 1.3ohm 24AWG SS coil...

I'm upto heat in less than 2 mins at 20W and vaping at just under 10.5W at the moment, with a slightly deeper bowl than shown above - and still tinkering around :science: I've backfilled the SS tube with glass balls above the bulb, as I'm using female crimp connectors as a bulb holder and cut 3...

thank you @blokenoname I built a Halo Bud Eater today and gotta say it's a teeny tiny beast!!

I rebuilt the new MA2/3 with a 10mm dia 1.85ohm coil today and put the previous coil in a smaller Claisen to compare :science: The 8mm coil works well in the 18mm Claisen at about 15W so I'd say that's OK as box mod portable (very similar to the super clapton build but with better heat...

Dunno if they're any good but you can put an older version of Arctic Fox on the Ultex T80

How you like the Coolest Hook? I keep looking at them (and J-hooks) but always end up using a whip instead :whip: My big bag o balls and the MA2/3 claisens finally arrived :nod: https://www.fishersci.co.uk/shop/products/quickfit-multiple-glass-joint-adapter-two-necks/12061603 1st...