Search results

The best method is getting on the waiting list by sending us an email to: mail@element-medical.ch More ash tree units will be ready by the end of next week! After this, I will make more ebony models, just received some pieces of this precious wood, it is very expensive, indeed! Thank you, vapman

And how many ribs has the vapman egg? This is not a coincidence!;) There are more ash tree units in progress! The ash tree is a common tree here Switzerland, because its toughness, the wood is widely used for tool shafts and less for furniture. When using the darker and lighter center part, it...

@gkaraman Try to get that black plastic ring out of your lighter, it will allow you to increase the gas flow with a screwdriver. The plastic ring is only pushed on to the valve screw. By placing the plastic ring in a new position, you can use it as before. Hope this helps!:) @scottg402 Thank...

@Chandler I will make ebony vapmans again, the wood is ordered but not here yet. Can't tell you, when they will be ready, I am careful and promise to have some before Xmas. I don't think you are drawing any pigments out of the plum tree mouthpiece, the wood is more likely to change its color...

Thank you everyone for participating and all the good wishes!!!:) Congratulations to @scottg402! I have to admit, I was a bit shocked at the first moment about another manufacturer winning the price, but I trust @Stu to have made a fair draw. Thank you @Stu! Well, as the manufacturer of...

@Michel:I don't think aceton would solve such burnt residues. Gentle scraping with a small knife will do the job! In case the tubes are badly clogged, you need a 0.8 mm drill to actually drill the residues out of the tube. Works great, I have revitalized vapmans, which looked like agent fossils...

The decreasing of the diameter inside the tubes is probably not caused by residues, the diameter decreases from 1mm down to 0.8mm just before the heating chamber! This step is needed for resting the tubes on a pin when doing the flanging. As mentioned before, unless you are blowing regularly in...

As soon someone provides me a drawing with the essential dimensions (angles, sizes) for an adapter, I will gladly grab a peace of wood and make some of these. Quite honestly, I need your help because I am not familiar with water tools and I don't know the exact need of the users of such devices...

@vagdal In most cases I think it is a good idea to let people make their own experiences, in this case I allow myself to tell you, that you won't find any alloy suitable for the mid-section. Metals and minerals get far too hot and plastics are toxic and don't withstand such heat in the long run...

Yes, definitely! I think this symbol, may be around 50mm (2 inches) large, will look good on a white or black t-shirt. I have to t-shirts with a nice cut. @Michel Thank you for the compliments! Think of vapman as a cooking pan, it is up to you, how and what you cook. The possibilities are...

Our brand new vapman symbol! The symbol will come in different colors corresponding to the egg shaped casings. I hope you like it! vapman

Installing the SS ring gives you the opportunity to adjust the spring tension on the locking system to your liking. In case you sand off too much, the bars will be below the springs making it useless.:doh: This is why I said above: check the spring tension during the sanding rather too often...

@ShinyMoonz I never used nor do I know tung oil, it supposed to be similar to boiled linseed oil and a good oil for protecting woods. I also learned that it is slightly toxic and therefore not food grade. I would definitely not use it on the mouthpiece (I don't treat mouthpieces at all), but may...

A few words about installing the SS ring (washer): When sanding down the mid-section, I strongly advice to check the spring tension during the process in order to make sure, you are not sanding over the point where the springs become too slack. Better check too often than too late!:nod: While...

@DrNick420 If it feels like the air restriction got bigger, it is most likely the inlets on the middle section that are clogged with condensates. Unless you have the bad habit of blowing regularly into your vapman, the nozzles normally don't get clogged at all. Besides this, there is so little...

I strongly disagree with you @OF! I believe everybody on this planet should have a piece of sandpaper, a small screwdriver and a swiss army knife, at the least! :lol: I am only joking, of course you are right! We will sell the mid-sections with the ring installed! Thank you all for the well...

To Celebrate the 10th anniversary of the Vapman, I would like to give away a Vapman station set to someone in the FC community. This is the winner's prize vapman station classic yew tree set Description of the content: vapman portable vaporizer for dry herbs and concentrates Heating...

The SS ring with the thin edge will probably cut up the mica washer. All you can lose is the washer, you have to try it out. The mid-section will come with the SS ring, but not pre-installed, giving the client the opportunity to adjust the locking system to his liking. Do you think this is a...

@MeesterWood I have not seen your station yet. I guess, that the docking part came loose and it is turning together with the vapman, making it difficult to place and remove vapman. The docking part made of aluminum is locked with a tiny allen screw (M2.5) and it probably came loose. In most...

@DrNick420 Thank you for the revealing posts, I learned a lot about the station I did not think of before. Funny, when doing the manual, I first mentioned to start at level 2-3 but abandoned exactly that sentence later on. Now, I know it was a good advice and it will be in the final manual. The...