Search results

Yes. They are very different, even dangerously so. The ones you need are quite special as I said. Do not use 3.7 Volt which are an entirely different chemistry (Li-ion rather than LiFePO4s). They charge to 4.2 Volts, two will put 8.4 on the six Volt heater and burn it out. The LiFePO4 is a...

Very valid point I think. To be expected for sure. The goal is to make it tiny without sacrificing too much, right? It's tiny, smaller than ArGo for sure (Arizer's attempt to shrink down Solo/Air). But, as you get smaller you face other constraints, you still need enough battery power to...

No, not an induction heater (that works by magnetic fields 'inducing' currents in nearby metal hence the name). Solo is conduction, not induction. Important difference. That said it might work? No harm in trying I can see. Then again, one could simply fill a handy Solo stem? OF

That's what it looks like. Mind, this is the SV (six Volt) version, not the standard one that runs on one 17650 Li-ion. The only practical way to run it is RCR123As for most folks, a system that was not popular 'in the day'. Still, IMO a great product, if you're prepared to deal with it on...

Beats me, they 'dried up' years ago AFAIK. If Randy says it's so, it no doubt is? But while Tenergy made chargers, Tracor made the transformers for the PA as I recall, and IIRC they were single primary? Only works with 110 VAC in. The one pictured here...

This is more than 'just a little' understatement. Steama gets fan mail from other hard to please types...... His vote of confidence says volumes IMO and should be well considered. He is wise, and a 'straight shooter'. OF

Unless you specifically ordered one, it won't. There were very few made, using a custom transformer (110 VAC only). There are alternatives if you're handy like this: But the parts inside (to make contact) will have to be made and a hole drilled in the bottom of the T1 for the...

Good points. I'm sure there are very happy owners, but there's also a lot of the other kind. AFAIK it's the only vape with it's own troubleshooting thread? Hard to have confidence when there are that many guys to support a 'how to fix your broken unit' discussion. Most of us buy vapes to...

You might want to check back carefully, that looks like the one from Amazon that was identified as being too tight to use the center section? That is the ID got smaller for the threads and a capsule would no longer fit, you ended up the the bottom and cap. I could, of course, have the wrong...

How about something in a nice little ArGo. Just the thing for a sport like you...... OF

NO!! IIRC only the lower capacity (600mAh) can supply the needed current, the higher capacity ones (900) have 'better numbers' but can't stand the duty. It may run longer but it won't get hot enough. And the batteries overheat trying? You really should search back and be sure. I suspect...

Yes, be sure your batteries are the approved ones, are in good shape and freshly charged. Be ready to swap them out. You herb should be well cured (dry, to very dry) an ground fine. Fill no more than 'to the rails'. Engage the battery but don't hit it until you see vapor condensing on the...

You know it's really too bad tipping isn't allowed on this Forum. If it were you'd be a rich(er) man today....... OF

Amen to that! Enjoy the Holiday, ya fer sure earndit. You're doing a great job/service, we can't be burning you out. That 'Golden Goose' thing? And rest up well, those orders will be backing up........ OF

Sure it can, but you'll have to make it convection (like GH) which really eats up the battery. As it is, IMO it's not really that bad. I've heard 'forty minutes heating per charge', and don't disagree with that. I can count on at least four loads, at two four minute sessions each. There's...

So 2/3 plus of that heating is from conduction? Not that I buy the math (remember we're assuming specific heat is the same for air as herb, which I don't think is the case) but doing 50 of the needed 180 degree rise is kinda cheating? Remember, in VC we are only allowed to heat air with a...

Hobbies are great, but IMO unless you're "missed your calling". Few indeed can control black and white to get such results. Even resorting to color and extensive editing. I'm betting your home has some very nice photos on the walls? Ansel Adams would be impressed, though he'd likely tell you...

I'm just better at it from experience. You know, talking my way out of tight situations? You should catch my act if you have a gun and badge........ Kidding aside (for just a moment), I used to get paid to teach this good stuff. I recommend retirement, however. I think such talk keeps...

Then you'll like PBW, it uses the same 'Oxygen action' as one component. Buffers keep the wash chemistry 'in line' so it's effective in hard/contaminated wash water and surfactants to break down surface tensions so the gas generation can actually 'get under' deposits (between them and the class...

Yep, I'd agree with that. To heat by convection the air has to be much hotter coming in that going out so it can cool enough to give up enough heat to make some vapor before it cools enough to condense that vapor again. That much heat available to heat the incoming air would combust the load...