Search results

Yeah, right. Warranty. LOL If you like it with water, I might suggest a DDave mod water wand. Very nice and DDave is superfast

Maybe you'll get lucky with a super August special.

I have the Sai and the DV3 and the and the and the and the...... as far as I am concerned they all sit in the drawer and I use the Arcadia Longmada Motar. Quartz cup that wipes nice and clean. Top flow. However, the thing about this one that puts all the others in the drawer is that it never...

The free gift promo ends today. Always FREE Shipping. That is an amazing plus depending where you are.

Take it out hot, not cold. Tweezers should handle the removal fine, when it's hot.

@stardustsailor Oops, I forgot to tell you that I 'mirrored" the other picture so it would match the layout of the other picture. On the component side of the board Pin 1 is easily identified by the dot, like you said. On the solder side, the pin 1 is the square pad. Sorry, I should have...

Take a look at these pics. I don't have photo edit on this computer so we'll have to speak it. LOL You can see pin 3 comes off the 14 pin ic directly to pin 5 of the smd chip and the only other connection on that trace is a resistor going to the output on the voltage regulator. ?? Does seem odd...

I don't think moderators have the privs to change an email address. They could probably send a new password but it would have to go to that registered email address. Here is something you might try... When was the last time you logged on with that username and password? Do you have access to...

Let's see if I can trace the pins on that mysterious K12 14 pin IC. I have done numerous searches to try to identify it and that logo is non-existent. If nothing else, I can log the data pin and see what it sends on startup. That should give us something. Not that it really matters what chip it...

One of the down sides of the lower priced models is the heating setup. Most of them are preset and not adjustable. That's a killer for me. The down side of caged units and plates is that you have to buy the press after buying the plates. And, even though it's only 60 buxs, just having to buy...

I'm not 100% sure how the cycle timing is controlled but I'm certain it could be changed. I'll see if I can figure out how it's done.

That's pretty neat. I like the concept. My first DIY prototype was very similar except I used an arbor press. The only problem I had with that design was having to hold the load under pressure for 2 minutes. I am an old fuck and holding that much pressure on something for that long was pretty...

This failure could be my fault. I have had all my units apart and I have added plugs and messed with them all. Plus, we could be driving these units way beyond their intended design. If you place a small item like a wax knife in the cup, it heats to incredibly hot in the couples seconds of a...

@stardustsailor and @Egzoset We are going to find out if you are correct. One of my units failed. I believe it is that proximity switch that failed. Thanks for the input, both of you. I am tracing the pins from the 8 pin SMD and from the 14 pin IC that controls the LED and the fan. At a quick...

The only thing needed to complete a DabPress set of plates is a simple and very inexpensive Harbor Freight A-Frame shop press. They retail for only $78 and Harbor Freight ALWAYS offers 20% off coupons so the final price is only $63. Pair this with a set of DabPress 3x3 or 3x5 plates and you have...

I don't believe Winegums sells vapes, does he?

Yeah, I think you're right. It was Baked who bought the package off eBay. And, I think it was the guitar noodler who originally said it didn't work and set everyone down the wrong path long ago. I don't recall who the original eBay seller was. Or, if he's a member here. I am working on a...

I'm not a user of Xenforo but mod privs usually allow a mod to 'CHANGE' the password on the OP's account. Then, PM the new password to the OP and he should be able to log into his old account. No?

For that matter, you can sell on Amazon. LOL Anyone can. Paypal has their own 'store' apps that are pretty simple. Shopify is a good alternative. Facebook now has it's own marketplace. Or, like Summer says, keep it personal and just go with the forums and IG.