Search results

OK, if you insist. :science: Meet Stubby.

:tup: Can you tell us what you did to get it working? A reset maybe.? By your description of the fault, it sounded like the temperature sensor. Your solution would be great information. TIA Perfect!!! :nod:

Great stuff. I love the concept here. However, this would also heighten the risk of stripping the threads on the lid as well. Would apply slight downwards pressure manually at the same time. And loosen while still applying slight downward pressure as well. Once those threads strip your in for...

Yeah, the indents will lessen a bit. Not unlike putty. Not sure if pushing down too hard as I don't "think" the bottom will move down. Maybe others can advise more as I have only pushed down once and as you not too hard. I'm down to only two thicker stems left so not too concerned. Been waiting...

All part of the learning curve. The sizes of the bowls do tend to vary somewhat and the Solo will fit the largest best. That black ring that you show has a bad memory characteristic. More like a firm mushy material. You can correct it by gently pushing around the sides pushing the material...

I'm still on the original screen. Blow it off between sessions and use a brush every 5-6 sessions. Only clean with ISO about every other brushing. The key is to brush on the ISO generously and keep the ISO agitated and keep dipping the brush to add more as to keep from evaporating. Keeping this...

This is the first report that I have read of this condition. Hopefully there has not been another change removing the true PA option. IMO, you should contact your supplier to see if any news has come down on this as you already have a working PA system and want to use it. :2c:

That would likely work but I think actual carbon would work better. Activated carbon on ebay

That's the postal system. It must have missed a scan. Sometimes it will stay in that state until you receive it.

I had edited the post above. Would not recommend the one I got but might be better ones out there. The size I got which did fit nice was: GS WATCH CRYSTAL XHD 20.25 25.5mm EXTRA HIGH DOME Google "high dome watch crystal" the numbers above will make sense if you start looking around. I remember...

Sure can. Empty 510 tube Knuckle Drip Tip Initially I was using an end in the empty tube with shrink wrap to fit the hole. Wasn't the tightest and would fall out when removing the cap. I have now drilled out the cap hole to fit standard 510 tips. Used a 11/32" drill and only drill as deep as...

You're jumping along there just great. Looking awesome. I really like the glass bowl. Looks ready to go. Just throw in a 1/2" screen and bet a drip tip could be work to fit into the end like in the Bull. Being able to see what's happening is a bonus for sure. Keep it up. Love seeing these...

Does sound on the low side. Was this the first charged run? Give it a couple charge cycles to confirm your numbers. If you can't get at least 5 per charge, I would complain. From what I've experiences as well as what folks have reported, you should get 6+ on average, most get 7+.

You're having double sessions. So that is bang on. 3X doubled up is 6 which is well in the ballpark.

I would think it goes back to original terms of sale. When you purchased the C1 did they state newest model? And was the C1 the newest at the time? If not stated than I would not expect a newest model automatically. Maybe if asked to see but don't think there would be any obligation on their...

I use 95% of the time with a PA. For me, means I charge every 3-4 days at my convenience when level gets down to 1-2 lights. I put my money on a bad battery. Reads full but fails under load. After some time without load the battery reads fine again.? Suppose it could be a bad connection as...

You're very welcome. The supply that comes with the unit is a 12 volt/ 1 amp charger. The same as old models. Old models would cut out the ability to turn on the heater while charging. The new units have been programmed/changed to allow use while charging. It turns down the charge to trickle...

Couple things being tossed around once again regarding old/new models charge/PA applications getting blended together. Let's start with the older units pre-2014.? The units monitors the power input and depending on the voltage determines the function. If it sees 7.5-9 volts it goes into, what...

Hey guys, I have changed my price structure somewhat and thought I'd let you all know. Basically I have rolled the shipping costs into the complete price. I have shipped enough now to make up an average cost to myself and decided to pass along the savings. The pricing for the AIO kit is the...

I figured you had made a custom supply. And looks great. The godzilla supply I used is not much for safety. With 120 amps available it would blow any short out of the way pretty quick. You could likely arc weld with it. My earlier attempts using a slicer circuit works well except even finding a...