Search results

Air finally got here, feels super cheap/janky/Chinese, especially the joint, I foresee this being an issue, regardless of how well they work on paper. Oh and fuck you CCA and your $60, yes SIXTY DOLLAR AH shroud that used to be $50, that used to be $40, that used to be $30, that used to be...

IMO, its because you don't know what smooth and not burned REALLY tastes like, I was exactly the same way, loooooooved super hot globbers off titanium, got me ripped and still to this day nothing can kick me in the chest like a hot ti dab.........but lower temps off better nails, by far the...

D-nail has made, IMO, the best effort towards something like this and also IMO, is completely garbage and frankly a bad idea to begin with. They obviously by their nature add mass to the joint and effect the fitment and sizing (much more then you'd think from insanely thin teflon) that makes...

Placed an order yesterday afternoon, USPS already had the actual package last night and is on the way. Already a better experience then 99.5% of the companies Ive dealt with in the hobby.

Why is all of this "surprising" to anyone....seriously? They were called out on ALL OF THIS so long ago, very poor internal builds, very different internals across "same" models, total lack of UL, CE or any true oversight of any type whatsoever and Ill still go on record as saying they prolly...

(glances over at Kube) So then we should be worried about August also now? Not really following you're logic at all, Id easily put a Red Queen with a functional AP mode up against ANY other enail controller and while it wouldn't top them in temp stability (until the built in 10 second delay is...

Blah blah blah........none of this conjecture matters, NOTHING is going to come of it (no litigation is going to be brought against anyone whatsoever) because at the end of the day it simply isn't worth anyones times to pursue unless they really want to TRY to get a pound of flesh...and...

Only improvement I (and everyone else should) care about is if they remove the middle hole, which is, IMO and IME the #1 weak spot....but thats not possible with keeping the Halos design.

Never lose that DAS!! The Ligers are only 30mm now if you get a Halo, you REALLY should get their V2 carb cap, everyone doubts it, then they get one and can't believe they doubted the numerous posts saying its really a critical part of the whole setup and generic stuff just doesn't hit that...

So just to confirm, ALL of the labels last week were bullshit, again, correct? GG CCA Once the temps come down a bit, Ill take you up on that (not due to doubts), looooooove shooting down 395 in my car.

https://www.highlyeducatedti.com/blogs/information/study-quartz-insert-performance-opaque-vs-clear Edit: Also a diff technique, and IMO if you're gonna mess with bangers n torches, is drop your material in a coolish bucket, cap it, and lightly torch the corner and bottom of the bucket until you...

Since this was in reply to something regarding cannabinoid extraction and vape efficiency.....I gotta say after taking a look, nothing jumps out at me as being anything stand out in those 2 areas over existing products. So my question is, specifically, how is this one different?

Its plenty, IME most enails use less then 165w at peak, Im pretty sure it depends on the heater coil you're using, but that cable can take more juice then your enail controller most likely.

Its just a standard PC power cable @Hollabackatcha posted a good link

IMO, a much better setup is using a low profile male18/male14 and use the 14/18f DI dnail joint, that way its easier to clean, and removes practically all the heat from your piece......and you get to keep the slim bases uptemp ease and cool down speed

Yarp, Auber are wired to dnail and can handle at least 250w coils

This might be the first Ive heard this, it was also my pretty clear understanding that the "PID" component was fully software. Could you mean a different internal temp sensor maybe? Even if so, its odd the girls never mentioned this is our rather verbose discussions about this specific issue and...

Yeah, Orange Pi Zeros, they COULD somehow stuff the usb header onto the io pins and put a usb bt dongle but really just swapping SBCs is gonna be the way its gonna go.

Im 99% certain the Skynet SOC does not have BT and Im 100% certain the Queen does not also so it will definitely be a hardware revision to get BT going. I do not at all want to goto a full BT setup, don't get me wrong I LOVE my Kube and how it works but I wish it had the option also..... wifi...

Where was "more reasonable cost" mentioned? IMO $300 for a Queen is a steal......if it does everything its supposed to