Search results

I hear you, I would like to try the short bowl but it doesn't look all that short in the pictures, does anyone know the height above the screen? Looks very similar to the Elev8 bowl that I already have.

I agree with this, I don't know if this is a Covid thing but if companies cannot serve their existing customer base, they should not go around launching new products and wetting the appetites of their customers without being able to deliver. I see this all over the place now in my job...

I have both and can second that, not the same fit and quality, wobbles a bit and doesn't seal completely. Just seems crazy that you have to switch to a different and inferior delivery system (the injector) for lack of a quality 22mm OD glass bowl that already exists!

I know this has been said many times before but I wish someone would just copy the plus plus glass bowl and make it available to this community, everything about that bowl is right, it is the right size, the head fits and doesn't wobble, and it stays relatively clean compared to other glass bowls.

I am using the 18mm Grav Octobowl with the Qaroma, similar to the CH Injector I believe. I can fit 1-2 scoops and the injector sits right on top of the herb, about as close as you can get to the heater. The glass screen is not the best and gets dirty quite quickly, I still haven't found the...

1) Flowerpot (95% of my usage) 2) E-Nano, best one-hitter available, needs longer draws so only use rarely now. 3) Can't say I have a favorite portable although I own many (early VAS), I don't vape on the go and normally only break out the Mighty when travelling

I was able to find the receipt, my coil is the 20mm coil for Auber RDK300A 9322 purchased on 2/4/2020, it barely fits the Qaroma (can't screw top down all the way, see pics I posted earlier), but it fits perfectly in the Ceroma which is more coil friendly and doesn't have the raised step.

Thank you for posting this information, I finally have confirmation that not all CH coils are the same, mine is definitely the kind that "barely" fits in the Qaroma.

How far up the bowl does that go, beyond the half-way joint? Has anyone tried loading all the way up to the bottom of the head? I haven't even tried the stock bowl yet.

My experience is very similar, waiting for a new coil for the Qaroma to fully test it. Broke out the Ceroma with the GRAV 18mm bowl just for kicks yesterday, I know the screen on this bowl is not ideal and gets dirty faster than others but at least the material is as close to the heater as it...

My setup is very similar to yours, I use the plusplus bowl with a dropdown at 575-590 except that I use fine grind and fill the bowl to the top so the bottom screen of the B1 is right on top of the material. Almost instant dense vapor if you preheat 10-15 seconds. I don't see the point of...

I haven't noticed any difference between the WeedEater and B1 so far, both don't trouble my throat and I can use them daily through a lot of water and cooling pieces. I use glass bowls exclusively, I notice a big difference in taste over titanium but I am not sure if they are actually easier on...

Thank you for the kind offer but I need to hold on to my CH equipment because I use it every day. I bought the Q on impulse because I love glass, I will stumble upon a coil that works eventually or just sell it. I hate conflict and the tone this conversation has taken, this is supposed to be...

Thank you again, I have all the information I need and will not impose on you anymore. I wish you all the best.

Thank you. I can confirm these numbers on my unit. Can you confirm that the cutout is ~10.5mm wide and ~5mm deep and that the raised bed is located adjacent to the left side of the cutout.

Mine is 16mm. I have never attacked qshop in any posts, I have no interest in qshop. I am looking for measurements and facts to make my unit work properly without spending a ton more money.

The coil travels up and down freely and hits bottom every time. The depth of the housing is ~16mm or ~14mm where the raised step is. The coil never drops far enough so the bottom wrap catches on the step, it just glides over. The step is located right next to the cutout, if the cutout were...

This is the best fit I can get with the 5-wrap CH coil, the top nut just catches the top threads and sits at an angle leaving a big gap all around. I am not satisfied by this and would never use it like this, I think the post and threads would break after a short time. The height of the coil is...

I have been trying to troubleshoot the issue with the manufacturer but that has gotten me nowhere, the only useful information I received from them is that there is a "raised step" at the bottom of the bowl where the coil sits, supposedly to keep the coil in place better. I feel that it is this...

Thank you for the suggestion, I will let manufacturer know with pictures so they don't think I'm making this up.