Search results

My vote would be for the most Innovative new vape. The “cool” thing about this vape is that the vapor is already cooled by design and while water cooling would be fun, it’s not necessary. :science:

I used a T20.

This is a very common problem that can be easily fixed. Most likely cause of this problem is the metal band that makes contact with the metal lid is not making good contact. You will have to follow the instructions In this thread to slightly remove the torx screw at the bottom and then either...

6-7 months? It seems those that have ordered recently have received their unit in about 3 weeks after placing their order.

I spoke with Tafée team support regarding my extended charging issue above. If anyone else encounters the same extended charging time, there are a couple of things to try before contacting support. First, you can try the reset procedure to see if that corrects the problem. If not, another step...

My new puck is taking 3 1/2 hours to charge from the flashing lights indicating it’s dead to full 4 solid lights. This is after performing the reset. Is this normal charge time for everyone else?

You may have accidentally spun the metal cylinder, which can cause that O-ring to come out. Don’t worry, it’s not too hard to replace as stated a couple posts up.

Most likely cause of this problem is the metal band that makes contact with the metal lid is not making good contact. You will have to follow the instructions In this thread to slightly remove the torx screw at the bottom and then either bend slightly the band so it makes good contact with the...

It’s not a choke! you can register your Bowle’ using this link https://tafee.com/support.html Just scroll down past the FAQ.

Tafée customer support is the “real deal” - I was amazed how quickly they responded to my issue with the heater remaining on and green LED 7-10 seconds after my draw. They gave me the directions to perform a reset on the device. The same issue occurred again after resetting so a replacement...

Some have taken the stem apart removing the Allen screw at the bottom. I have found it’s just as effective pouring warm ISO into the stem and shaking vigorously for a couple minutes and then rinsing with hot water. If it’s got a a lot of oil buildup, I will usually keep refilling the stem and...

I had sent support an email after posting here and they advised to perform a device reset, which did seem to work for the first bowle, but the issue seems to have reappeared again on the second one. For now I am just going to manually press the button to activate the heater. Tafée customer...

I performed the “reset” per Tafée instructions and now have to wait an hour before testing it again. 🤞

No the button has a firm rebound once pressed. I am not sure, but seems like an issue with the breath sensor?

Has anyone noticed the breath sensor not disengaging the heater after you finish your draw? It has been happening more frequently on my unit. I push the button, start my draw on the green LED, stop drawing, and the heater and green LED remain on for about 8-10 seconds unless I power off with...

I have found that this vape is so simple to clean. Simple enough that I felt it was safe to bring along on my Mexico vacation last week in my carry-on bag. I know it was a risk, but nothing occurred except good times in Mexico. Luckily, I was able to find a convenience store that sold...

TM owner here and the buzzing noise as stated above is completely normal.

Before I placed my order, I had asked the Tafée rep this question and their reply was that the size does not make a discernible difference in cooling. He further advised, if my intent was to use sans cup, the shorter stem would most likely be preferred.

Mighty dosing capsules are too big and will not fit in the TM stem, however some, including myself, have previously used them carefully placed under the stem. It is required to slowly insert the stem so you don’t push the capsule through the TM heater screen and onto the coil. IMO, it’s not...

Leave the screen in place when cleaning - it shouldn’t be necessary to remove. The CU pieces go back together as such - take the half that has the shaft and then add in this order - nut, washer, nut, washer, nut then screw both halves together. Note, there will be a gap between both halves...