Bonesvapechi
Well-Known Member
What are the dimensions and thickness of the o-ring for the bottom heater? The o-ring just pops out now almost making my unit unusable
-
SCAM WARNING! See how this scam works in Classifieds.
-
The Frolic by Limelight Giveaway has started!
ConVex by Entheos Devices (formerly Tokedvapors)
- Thread starter iDRINKBLEACH
- Start date
Are you referring to the o-ring above the bowl?
Just Justin
Well-Known Member
Can we see some detail photos of the device? Especially interested in the new updates; ceramic base, new mouthpiece, battery door button etc. eventually it would also be interested to see a step by step of coil replacement process…much appreciated
Side note: I’ve used my V1 multiple times almost every day since it was first released without a single issue and the coil is still going strong, so I imagine coil change is not a frequent occurrence anyways
Bonesvapechi
Well-Known Member
Yes, I bought a new device couple months back and the oring maybe too thick? I noticed instantly that the bowl was a little too tight and it took some work to swivel the bowl out. Then one day pop, the oring surrounding the heater on top popped off
in my experience, this happened to me seldomly when the bowl swivel was not aligned perfectly - which was often caused by the metal connector that clicks into the fins, perhaps play around with the position of the connector because that will affect how the bowl sits with the unit
Bonesvapechi
Well-Known Member
I’ve played around with it. Even if I adjust it, it eventually pops out
TigoleBitties
Big and Bouncy
For those of you who own the device, what kind of battery life are you getting i.e. how many bowls per full charge on average?
@Entheos Hex , are there any future plans to build a unit that will accept a 21700 battery?
@Entheos Hex , are there any future plans to build a unit that will accept a 21700 battery?
Bonesvapechi
Well-Known Member
I use the standard molice? Whatever it’s called lol. But I actually get about 10-20 bowls depending on usage. I use it as a one and done hit
TigoleBitties
Big and Bouncy
Wow. 10 bowls on the low end is a lot, but if all your bowls are a one-and-done hit then I'm not sure I have the same vaping style. I use the Bowle2 which is a similar convection-only on-demand device but I'm at least taking two hits per bowl.
Bonesvapechi
Well-Known Member
Yeah I have it configured to where it works like a TM but everything like a TB2
TigoleBitties
Big and Bouncy
Ok so you crank up the power and do one-and-done microdoses or full bowls? You're using a power level similar to Bowle level 5?
Just Justin
Well-Known Member
I would agree and get a minimum 10 bowls on a charge with a good battery. I typically run at 388f and take 5 rips or more per bowl. I have a Tinymight 2 and Tafè Bowle and I get significantly less bowls per charge than the V1 with those devices. The coil on the TinyMight 2 is much larger than the V1 and the Tafè Bowle is closer in Size to the V1 but has a small battery pack in comparison.
I redesigned my Tafè Bowle to accept 18650 and use a temp control chip instead of their electronics and it’s probably pretty close to the V1 in performance now
I redesigned my Tafè Bowle to accept 18650 and use a temp control chip instead of their electronics and it’s probably pretty close to the V1 in performance now
I was fortunate enough to spend some time with the V1. Absolutely cannot wait for the upgrade. Everything about this vape suits my vaping style. Fast to heat, easy to load, full convection, great ergonomics. Thanks Entheos for staying in the game. I will be looking forward to the release of the V2.
TigoleBitties
Big and Bouncy
That's amazing efficiency with one 18650.
The Bowle2 has a huge battery pack so I guess you're referencing the Bowle1?
You redesigned your Bowle? Nice! Again, I'm guessing this was a Bowle1?
Bonesvapechi
Well-Known Member
I would pay you to reconfigure mine lol
Just Justin
Well-Known Member
Here are a few pics of the Tafè “ Box”
It’s a bit big for your pocket but the main goal of this project was to power my Tafè Bowle with a removable battery and have full temp control. Anyways, pretty much just cut around the heater and built a box around it, filled it with a battery and added temp control mod electronics
It’s a bit big for your pocket but the main goal of this project was to power my Tafè Bowle with a removable battery and have full temp control. Anyways, pretty much just cut around the heater and built a box around it, filled it with a battery and added temp control mod electronics
TigoleBitties
Big and Bouncy
Very cool!Here are a few pics of the Tafè “ Box”
It’s a bit big for your pocket but the main goal of this project was to power my Tafè Bowle with a removable battery and have full temp control. Anyways, pretty much just cut around the heater and built a box around it, filled it with a battery and added temp control mod electronics
Do you mod a lot of your vapes in general? You make it sound like this mod was a walk in the park. Well done!
Back to the Convex though... 10 bowls with an average of 5 draws per at 388F is really great in my eyes for one fully charged 18650. Add to this the new ceramic parts and the retractable stem and this device is looking very good.