• We are experiencing temporary outages. Keep trying, it does recover. We hope to rectify this as soon as possible.

Recent content by Caliban

  1. C

    The Tempest by Mad Heaters & Phatpiggie

    I have, but much prefer the T2 stem I think, but mainly because I much prefer using it on a piece via the WPA.
  2. C

    The Tempest by Mad Heaters & Phatpiggie

    I never got on with the Dynavaps personally. I've tried quite a few and I've sold them all since getting my tempest 2. All I have now is a T1 and T2. They are miles ahead of the Dynavaps in my opinion, it's not even a close comparison. For me, the Dynavaps are too tight on the airflow and I...
  3. C

    The Tempest by Mad Heaters & Phatpiggie

    Yes it did. I think it helps the end of the reload tool is a little sticky, so it holds the screen nicely. @Grass Yes Using the reload as a funnel is an ingenious idea! I'm going to try that next time thank you.
  4. C

    The Tempest by Mad Heaters & Phatpiggie

    @BearFuur Have you tried using the screwdriver / debowler tool that comes in the Reload 2? I find that works perfectly for doing the ball screen.
  5. C

    The Tempest by Mad Heaters & Phatpiggie

    For those of you using the V2 wand adaptor and the tempest 1, do you set the depth the same for tempest 1 and 2?
  6. C

    The Tempest by Mad Heaters & Phatpiggie

    If I remember correctly, some of those videos with loads of hits were using hash and flower. The hash can go for ages. I also find slightly more humid material gives off much more vapor. Silly question I'm sure, but you do have it set to full bowl?
  7. C

    The Tempest by Mad Heaters & Phatpiggie

    I prefer them for the smaller bowl settings. I do think the zirc are the best for clearing the full bowl setting without having to go up to a really high temperature on the wand. Am I right in thinking that because the wood sleeves are stabilised, we won't need to wax them etc?
  8. C

    The Tempest by Mad Heaters & Phatpiggie

    I will hold of another gen 2 and wait to see what's updated and get some new colours! Thank you.
  9. C

    The Tempest by Mad Heaters & Phatpiggie

    Are there any changes to the reloads and will they be available in the new colours?
  10. C

    The Tempest by Mad Heaters & Phatpiggie

    These are all so nice! Are you still just doing these with a drill? I wish I could help with the mystery wood type.
  11. C

    The Tempest by Mad Heaters & Phatpiggie

    Airflow is much simpler on the V2, it's just the adjustable airflows on the cap and then the rush hole open or closed.
  12. C

    The Tempest by Mad Heaters & Phatpiggie

    You can indeed just pull it straight out. It's held in by two o rings.
  13. C

    The Tempest by Mad Heaters & Phatpiggie

    I'm not sure which page it's on, but there is a guide with picture in this thread.
  14. C

    The Tempest by Mad Heaters & Phatpiggie

    Thank you for uploading! That looks like the C tool for setting the bowl depth. The ones we've seen so far have been 3d printed, so it's good to see a proper version! I didn't get either version and it is a bit fiddly to adjust the bowl without it. I wonder what the tiny little hole is for 🤔...
  15. C

    The Tempest by Mad Heaters & Phatpiggie

    Very interesting, could you post a picture of the C tool? The bowl should just pull away from the stem?
Top Bottom