AirVape Legacy Pro

imor jones

Well-Known Member
No i havent tried my SE LP yet at all.
But when i cleaned it, j realized that the bowle is loose. I can turnt it in the vape.
I remember somebody else mentioned that. Is it sth to worry about.? Or does that not matter much? Somebody knows?
Thanks
 
imor jones,

seedy53

Well-Known Member
No i havent tried my SE LP yet at all.
But when i cleaned it, j realized that the bowle is loose. I can turnt it in the vape.
I remember somebody else mentioned that. Is it sth to worry about.? Or does that not matter much? Somebody knows?
Thanks
oven bowl or dose cap?
 
seedy53,

imor jones

Well-Known Member
the bottom screen, it should be lose an spin during vaping i believe
But the bowle of my og avlp is not loose. Only my avlp steampunk has a loose bowle.
I will use it soon, since there is this pattern thing now. I dont get, what it is about...
 
imor jones,

seedy53

Well-Known Member
But the bowle of my og avlp is not loose. Only my avlp steampunk has a loose bowle.
I will use it soon, since there is this pattern thing now. I dont get, what it is about...
don't have se so i do not know, have you tried beast mode?
 
seedy53,

Kaaotic

Active Member
My Legacy Pro's bowl bottom spins. Doesn't seem to affect anything. But I'd like to know if this is normal.
 
Kaaotic,

imor jones

Well-Known Member
I tried the beast mode yesterday.
Its a temp stepping mode. Starts with 200 C Celsius for 30 sec, then 205 C for 20sec, 215 C f0r 15 sec and 230 C for 5 sec...the last step with 230 C called the beast Level.
The bottom of the bowle is spinning. But doesnt seems to affect anything
 

seedy53

Well-Known Member
I tried the beast mode yesterday.
Its a temp stepping mode. Starts with 200 C Celsius for 30 sec, then 205 C for 20sec, 215 C f0r 15 sec and 230 C for 5 sec...the last step with 230 C called the beast Level.
The bottom of the bowle is spinning. But doesnt seems to affect anything
hell the reg alp goes to 464f
446f for beast mode is not a boost, it's a temp cut. why make se a lesser heater?
 

vandalizedbythelotus

Well-Known Member
hell the reg alp goes to 464f
446f for beast mode is not a boost, it's a temp cut. why make se a lesser heater?
i think it's more like a beast mode session, with automatic temp stepping, going up to the max temp meant for herbs. i'm sure the heater goes up to the same 464f in wax mode.

p.s. both my units bottoms spinning
 

seedy53

Well-Known Member
i think it's more like a beast mode session, with automatic temp stepping, going up to the max temp meant for herbs. i'm sure the heater goes up to the same 464f in wax mode.

p.s. both my units bottoms spinning
how is temp stepping be a beast mode? top beast is 446f. where is our rep, Gary?
 
seedy53,

MrBaked.co

Well-Known Member
As I sit in the bath vaping on my AVLP at 150c, chugging big clouds, I wonder how accurate the temperature is. 🤣

I was honestly getting fed up vaping. I've been fed up with the heat and sore throat I get for a while and I actually took over a week off the weed for the first time since 2019 when I went on holiday and couldnt get any.

This is the first time I've had weed around and not used it for that length of time since I started over 20 years ago. It wasn't planned. I just woke up one day and though fuck it. And that turned into about 8-9 days. I only became a legal user in the UK 1 month ago 🤣.

Ive been so fed up recently I've been slowly selling all my vapes. I sold loads ages ago but recently I started with all my "forever" vapes like the tubo dual, then my Toad, and next will be my tinymight 2 and mighty+ and finally my puffco peak pro with 2 grams of some insane bho 🤣 that I don't wanna vape anymore.

All I'll be left with is my dynvap(just incase the world goes to shit) and my AVLP.

I just absolutely love this thing. Since buying my first magic flight launch box in about 2016'ish i think?? I have never found the perfect vape for my user experience, you know the does it all vape until now. The AVLP with the capsules which I seem to have got lucky and have 2 capsules that are basically push fit lids then use the tool to screw off(fuck knows how but it's great). And I decided let's see how low I can go for my throat. I started at my usual 185 and went down 5c per bowl over the last 5 days and found that 150 is my sweet spot. It takes a few draws to get going but after that I can get a good 10 mins of decent clouds and the avb is a nice light brown consistency. People can say it may not be 150c in reality but from my experience as a low temp vaper I'd say it can't be far off. I can kinda tell by the throat that it's not as hot.

Anyway, I'll be putting my tinymight2 and various stems and other bits and bobs up soon and probably won't be around to much as I'm leaning towards edibles these days so I thought I'd say my fairwell(for now) in this thread as its one of the only vapes i will try and keep up with all the goings on, mostly as a reader.

Much love to you guys as ive leanred everythng i know on this forum and to Gary and the team for such a great piece of kit that just delivers mighty+ experience in a far superior piece of equipment in every possible way.

Makes you wonder why storz n bickel haven't done anything this good in 10x the time. They'd rather just milk off all the reviewers to make sure their dinosaur tops all the best vape lists because its easier than listening to the end user and working hard like airvape, tinymight and even "little" companies like the one with the xmax v3(the name escapes me).

Credit where credit is due.

Peace out 💚
 

shane1

Well-Known Member
Anyone find a convenient way to carry around loaded dosing capsules? I was a review regarding the capsules on the Airvape website and it looks like they fit inside of a Doob tube. But which one?
 
Last edited:
shane1,

greenpager

Well-Known Member
I am not panicked but I am ... so very sad.

As of last night, my ALP powers on but, no matter what temp is set, does not heat beyond 67-68° F(arenheit)! I can't figure out where to start troubleshooting. Has anyone else experienced this problem?

Original battery, recharged via external charger, dosing capsules, no drops/rough treatment. So deep is my disappointment - I am putting this away for tonight (thx Roffu). Maybe things will look better in the morning. 😮‍💨
 
greenpager,
  • Sad
Reactions: Spin0620

imor jones

Well-Known Member
I received my og avlp 5 weeks ago.
And my steampunk 3 weeks ago. But started to use the steampunk just a few days ago.
And somehow i have the impression, that the steampunk hits harder than my OG. And the avb gets darker. Even when i put the temp of my og on like 200 and the steampunk on 180 i think its hitting harder.
Also it feels like the airflow of the steampunk is more free. And more restricted on my og.
I would say that my steampunk hits like 10% harder than my og.
In the beginning i thought maybe my og is too dirty and because of this less free airflowing and less good Performance. But i cleaned all parts, and have the impression that the restriction is caused below the bowle area, so not above the herbs where all the screens are coming.

But i am not 100% sure with my findings.
Also it could be, that the temp callibration of my two vapes is just different and so one is hitting harder, than the other.

So, i wanted to mention my finding and want to ask if somebody else have similar findings.

Maybe also differences between different og units and not only with a steampunk unit...
 

Spin0620

Well-Known Member
I am not panicked but I am ... so very sad.

As of last night, my ALP powers on but, no matter what temp is set, does not heat beyond 67-68° F(arenheit)! I can't figure out where to start troubleshooting. Has anyone else experienced this problem?

Original battery, recharged via external charger, dosing capsules, no drops/rough treatment. So deep is my disappointment - I am putting this away for tonight (thx Roffu). Maybe things will look better in the morning. 😮‍💨
Well there is a warranty. I would get in contact airvape. Maybe @Gary-Airvape can help.
 
Spin0620,
  • Like
Reactions: Okla68

seedy53

Well-Known Member
I received my og avlp 5 weeks ago.
And my steampunk 3 weeks ago. But started to use the steampunk just a few days ago.
And somehow i have the impression, that the steampunk hits harder than my OG. And the avb gets darker. Even when i put the temp of my og on like 200 and the steampunk on 180 i think its hitting harder.
Also it feels like the airflow of the steampunk is more free. And more restricted on my og.
I would say that my steampunk hits like 10% harder than my og.
In the beginning i thought maybe my og is too dirty and because of this less free airflowing and less good Performance. But i cleaned all parts, and have the impression that the restriction is caused below the bowle area, so not above the herbs where all the screens are coming.

But i am not 100% sure with my findings.
Also it could be, that the temp callibration of my two vapes is just different and so one is hitting harder, than the other.

So, i wanted to mention my finding and want to ask if somebody else have similar findings.

Maybe also differences between different og units and not only with a steampunk unit...
we need to know if this is true @Gary-Airvape
 

TigoleBitties

Big and Bouncy
I received my og avlp 5 weeks ago.
And my steampunk 3 weeks ago. But started to use the steampunk just a few days ago.
And somehow i have the impression, that the steampunk hits harder than my OG. And the avb gets darker. Even when i put the temp of my og on like 200 and the steampunk on 180 i think its hitting harder.
Also it feels like the airflow of the steampunk is more free. And more restricted on my og.
I would say that my steampunk hits like 10% harder than my og.
In the beginning i thought maybe my og is too dirty and because of this less free airflowing and less good Performance. But i cleaned all parts, and have the impression that the restriction is caused below the bowle area, so not above the herbs where all the screens are coming.

But i am not 100% sure with my findings.
Also it could be, that the temp callibration of my two vapes is just different and so one is hitting harder, than the other.

So, i wanted to mention my finding and want to ask if somebody else have similar findings.

Maybe also differences between different og units and not only with a steampunk unit...
My guess would be cleaning. A dirty airvape can degrade by 10% efficiency easily imo and the steampunk has only been around for a little while so possibly it isn't as dirty - don't know your usage/cleaning. Do a deep clean and maybe try again.

Also, I don't think the holes on the bottom screen of the bowl are ever meant to be cleaned. How do you even get under the bowl?
 

seedy53

Well-Known Member
I tried to clean the holes of the bottom screen of the bowle. Maybe they are clogged from vaping oil. But whats the best way to clean those holes
for the oven, turn empty unit upside-down and use a tightly wound cotton q-tip dip it with 91 to 99 percent iso and rub it clean (chamber) in upside-down position.
repeat till clean and let it evaporate while in upside down position for about 5 mins or wipe it out with a fine cotton cloth.
that's my method and maybe a little extreme
 
Top Bottom