1. What does SSTB mean? See our glossary of acronyms.
    Dismiss Notice

tubo evic

Discussion in 'Portable Vaporizers' started by funkyjunky, Oct 21, 2016.

  1. sickmanfraud

    sickmanfraud Well-Known Member

    Messages:
    1,454
    @Jah1975 Have you tried putting your medicine in an internal basket screen then using the rimmed screen as a "cap" for the stem?

    @aaaalex welcome to FC. Coils are NOT supposed to glow. See if @funkyjunkie has a record of the proper resistance settings.

    @mrbiggiejones welcome to FC. As I mentioned (as well as many others) the coils are NOT supposed to glow under normal conditions.
     
  2. frosty234

    frosty234 Well-Known Member

    Messages:
    125
    Coils are not supposed to glow, even in warm up mode? Mine do glow very slightly and just in warmup mode. Is that bad?
     
    Padriano and funkyjunky like this.
  3. funkyjunky

    funkyjunky www.lamart.ch Manufacturer

    Messages:
    386
    hello friends!

    what do you mean by "temp cuts off"? as @pakalolo said i have had this with my cuboid150w, and think its the button on this particular model. i think the buttons on the evics (vtwo mini/vtc dual) are not affected by this and should work all the time.

    here is a video how to flip the screen (all models running tubomyevic should flip):
    Click to play YouTube Video

    also @SloJimFizz you can see how to flap the flappybird


    the warmup mode heats always to 245degC and keeps the heater on temp until it uses less than 20watts to maintain, then it autoshuts itself off.

    hmm. can you send me your order number in private? sloppy to not have included the resistance, it should be written on the bottom side of the battery door, there is a little space of wood under the metal part.
    yes as others have said, the coils should not glow. they might do so very slightly at 245degC-260degC in the dark. if you can see it in daylight, the coil resistance in the menu is too high.

    warmup mode is only "working" properly when the tubo is cold and needs a warm up. it should run around 10 to 30seconds. after the initial warmup cycle a repeated warmup will terminate very quickly since the coils are hot already.

    if warmup runs for 40seconds+ the coil resistance is likely too high.

    cruise mode should not cut out.

    as @sickmanfraud correctly said: coils should not glow.

    yep. they might glow slightly in the dark. bright red coils indicates a too high coil resistance.
    there are discussions around bright red coils degrading faster.



    to get guaranteed results with the tubo:

    lets see if we can get you on track.

    please check that the value on the line COIL is the same as the one indicated inside on your battery door.
    if not, adjust it in 'menu>coils>manage' at the line TCR, make sure the lock symbol is there when you leave the menu.

    take your stem, remove the metal basket screen and fill your material inside the glass joint. cap it with the basket screen and insert into tubo.
    tripple click the fire button to engage "warm up" mode. it will run for something between 10 and 30 seconds (only the first time, after that it will terminate quickly). then set it to 200C or 400F and double click the fire button to start "cruise mode". draw steadily for around 15 seconds, maybe at increased inhaling speed as the tubo likes that. by the seconds draw it should produce clearly visible vapor. if you continue to do this you should get baked ;)









    capsule stem samples are in!
    [​IMG]

    vapcap compatibility brought to you by @Padriano! big up! also the mouth end will fit 14mm glass joins.
     
    Last edited: Mar 13, 2018
    grokit, vapen00b, boon and 21 others like this.
  4. frosty234

    frosty234 Well-Known Member

    Messages:
    125
    Wow looks good! You can't definitely count me in as soon as they're available for purchase.

    My coils are just glowing slightly in the dark and only in warmup mode which I barely use, no glowing in cruise. Just wanted to know if that's a good indicator to get the right coil resistance settings.
     
  5. SloJimFizz

    SloJimFizz Unknown Member

    Messages:
    698
    Location:
    Joe's Garage Jamming
    :tup:
    Sweet, just scored a 20 on Easy.
    The Tubo got just a tad better today. :D
     
    vapen00b, Aezhenn, Padriano and 2 others like this.
  6. muunch

    muunch hotboxing the cockpit

    Messages:
    1,735
    love the wood stems. can the elb tops be used to seal them up so no herb falls down onto the heater screen?

    regardless i think im gonna have to get one once out of prototypying :tup:
     
    Aezhenn, Padriano, Gray Area and 2 others like this.
  7. szai

    szai Well-Known Member

    Messages:
    754
    Location:
    Florida
    Thats kinda fantastic! The tubo has been in my thoughts more and more recently.
     
  8. aaaalex

    aaaalex Member

    Messages:
    3
    Now that the settings have been figured out, I thought I'd post a picture! I'm obsessed with the colors:drool: [​IMG]
     
  9. Padriano

    Padriano Company Representative (Lamart Tubo)

    Messages:
    30
    Thanks for the shout out @funkyjunky . I'm now expecting 30% of all future profits!

    It's also worth bigging up @Aezhenn , who did such a good job of turning the stems.. Thanks dude! :bowdown:

    I've been 'testing' for nearly a week now, and they've been working great. There are a few small tweaks to be made before the production run, but I'm happy enough with the one's I've got ;)

    This stem is particularly nifty:

    Mighty capsule
    [​IMG]

    Vapcap
    [​IMG]
    14 WPA (vapcap or tubo/Mi). Perfect fit.
    [​IMG]

    Pretty versatile! Theoretically it could also be used as an 18mm WPA with the vapcap at the mouth end too.. And it will work as a regular stem without the capsule.

    I've had no issues as of yet.. The capsules hold well but pull out easily, the draw resistance is still non existent, and the roasting is pretty even. I would struggle to go back to the old system now, and even more so when the glass inserts are sorted!

    Life's a beech
    [​IMG]
    It really ties the vape together :luv:


    [​IMG]
     
    Last edited: Mar 14, 2018
  10. szai

    szai Well-Known Member

    Messages:
    754
    Location:
    Florida
    I have an evic vtc dual can I order the tubo without it? How much does a dual cost without the evic?

    Thanks
     
    Last edited: Mar 14, 2018
    funkyjunky likes this.
  11. SloJimFizz

    SloJimFizz Unknown Member

    Messages:
    698
    Location:
    Joe's Garage Jamming
    You are after the TUBOx I think.
     
  12. szai

    szai Well-Known Member

    Messages:
    754
    Location:
    Florida
    I've seen that model I meant ihave the same box mod that's used in the tubo evic.
     
    funkyjunky likes this.
  13. SloJimFizz

    SloJimFizz Unknown Member

    Messages:
    698
    Location:
    Joe's Garage Jamming
    Ah. I see.
    Think it's hard wired into the mod and the wood boxing in all the parts.
    Can't see swapping evics in and out being all that easy
     
  14. szai

    szai Well-Known Member

    Messages:
    754
    Location:
    Florida
    I don't really care to swap it out, I'd be fine with just mailing it in if i needed to.
     
    funkyjunky likes this.
  15. sickmanfraud

    sickmanfraud Well-Known Member

    Messages:
    1,454
    I believe that sending your evic to Switzerland would be the same cost as buying a new one from @funkyjunky as part of a Tubo.
     
  16. szai

    szai Well-Known Member

    Messages:
    754
    Location:
    Florida
    Oh didn't realize he was in Switzerland.
     
    funkyjunky and Padriano like this.
  17. funkyjunky

    funkyjunky www.lamart.ch Manufacturer

    Messages:
    386
    exactly. it is possible to include an old mod but probably not worth the shipping.




    yes of course @Aezhenn needs a big shout out for his awesome work! he got it like 99% perfect without having a glass joint in the first place.




    i am in need of some brave souls for testing a new firmware version. interested individuals are kindly asked to contact me via pm, thanks! :D
     
  18. Aezhenn

    Aezhenn Well-Known Member Accessory Maker

    Messages:
    612
    Location:
    Er C'hornog
    @Padriano @funkyjunky Thanks to you guys!
    I'm happy to collaborate a little to the Tubo project! :science:
     
  19. Lana Studios

    Lana Studios Member

    Messages:
    8
    Tubo arrived today exactly one month after i ordered it:lol: I cant wait to get home and test it out
    :science:
     
  20. awmaster10

    awmaster10 Well-Known Member

    Messages:
    23
    Pictures or it didnt happen! Or at least tell us the color scheme. 5 days in and still loving it, cruising at 380 as we speak.
     
    funkyjunky and SloJimFizz like this.
  21. little maggie

    little maggie Well-Known Member

    Messages:
    3,117
    I love these but wish that one of the wood ones would fit a whip. So far I haven't found one.


     
    funkyjunky and Padriano like this.
  22. RelaxedNow

    RelaxedNow Well-Known Member

    Messages:
    546
    Yes, but if you’re willing to go with wood AND glass, funky is working on that, per this video.

    [QU]
     
  23. Lana Studios

    Lana Studios Member

    Messages:
    8
    My Evic keeps switching to power mode help
     
    funkyjunky likes this.
  24. Lana Studios

    Lana Studios Member

    Messages:
    8
    I cant use my evic the coil keeps glowing read and everytime I try to go into cruise//warmup/ on demand it takes me out of TCR and puts me in Power mode Idk whats going on with it please help
     
    funkyjunky likes this.
  25. NizzyJones

    NizzyJones Well-Known Member

    Messages:
    149
    This page has the extended manual: http://tubo.lamart.ch/#manual

    Sounds like you need to check the TCR setting (‘menu>coils>manage>TCR’) and make sure it matches to one inside the battery door.
     
    funkyjunky, Rasputin and Padriano like this.

Support FC, visit our trusted friends and sponsors