Search results

  1. welderboy

    Flowermate V5Nano by Smiss

    I think the airflow is pretty good, naturally there is restriction, but not too bad. It took a little bit to get used to, since my e-juice mod and my bubbler have no drag at all. Long, slow pulls seem to work the best for me. P.S-----> my bad ,,,the charger is not pass through, the device shuts...
  2. welderboy

    Flowermate V5Nano by Smiss

    Got my Nano today ,,,still playing around with temps, packing and grinds. So far I'm pretty impressed. Great flavor, good hits, lightweight and compact. Love the removable 18650 battery since I already have a bunch for my e-juice mods. No more getting stuck with a dead battery, plus it has a...
  3. welderboy

    Discontinued Pax Vaporizer by Ploom

    I had to return my Pax due to a broken temp button, so I un-soldered my bullet connectors and re-soldered the original battery back in. One of my O-rings was broken so I crazy glued it in place and put my Pax back together. Sent it back to Ploom and crossed my fingers. I received an e mail the...
  4. welderboy

    Discontinued Pax Vaporizer by Ploom

    Am I the only absent minded stoner, or has anyone dumped their load into the wrong end of the pax, c'mon and fess up....lmao
  5. welderboy

    Discontinued Pax Vaporizer by Ploom

    Definitely, the case itself smells like peppermint(or whatever flavor gum). If the case gets stinky after awhile just chuck it and get a new one.
  6. welderboy

    Discontinued Pax Vaporizer by Ploom

    the mentos gum case is a perfect fit for the pax. I cut out the section below the cap because its too small, then used the cap on the mp end and used the rest of the case over the other end. you could also cut two cases in half and slide them over each end.
  7. welderboy

    Discontinued Pax Vaporizer by Ploom

    AK02621 single party mode, replacement last December, modded out and running like a raped ape.
  8. welderboy

    Discontinued Pax Vaporizer by Ploom

    I made this at work, tamper on one end, stirrer on the other. I can also remove the spring with the stirrer end.
  9. welderboy

    Discontinued Pax Vaporizer by Ploom

    http://www.ebay.com/itm/0-8-mm-Micro-Bullet-Connector-for-ESC-Brushless-Motor-US-Seller-/121085290094?pt=US_Radio_Control_Control_Line&hash=item1c313ee66e I used these connectors, soldered the male ends on the pax wires and the female on the battery tabs, covering everything with heat shrink...
  10. welderboy

    Discontinued Pax Vaporizer by Ploom

    I hook an 18/14mm adapter to the mp with some 1/2" silicone tubing(no crazy glue)...it's non destructive and works great
  11. welderboy

    Discontinued Pax Vaporizer by Ploom

    No mods..... I just made sure the batteries were no longer than 66mm. I can put eveverything back together in original condition should I need to return it.
  12. welderboy

    Discontinued Pax Vaporizer by Ploom

    I was getting about 1hour 15 minutes of high temp(red), continuous, on party mode with the original battery. About 1hour 45minutes with the Chinese 3100 maH. And almost 2 hours with the Panasonic 18650a . There is a Panasonic 18650b which has more power (3400) I think.
  13. welderboy

    Discontinued Pax Vaporizer by Ploom

    Not anywhere but this thread.....I've used generic Chinese batteries and now I have a Panasonic in there. Lol I'm no expert, but I like to tinker....
  14. welderboy

    Discontinued Pax Vaporizer by Ploom

    Now I have a Panasonic 18650a in there (green battery in pic). I keep that one in there most of the time. The purple ones are Chinese generic, and they work fine too. The Chinese ones are protected and the Panasonic isn't. No problems so far......
  15. welderboy

    Discontinued Pax Vaporizer by Ploom

    did someone say batteries? Lmao
  16. welderboy

    Discontinued Pax Vaporizer by Ploom

    The edges of the screen are scalloped and the air flows through the gaps between the screen and the oven wall
  17. welderboy

    Discontinued Pax Vaporizer by Ploom

    I'd buy another in a minute,
  18. welderboy

    Discontinued Pax Vaporizer by Ploom

    I had my pax replaced once for an internal issue. Received a new one in a week, ploom service is top notch.
Top Bottom