Recent content by philosopher

Finding a good solar setup is easy, but as far as I know there is no straightforward way to charge the Mighty directly from the sun. With that said, there are plenty of power packs that can charge via solar in a respectable amount of time, which can then be used to charge the Mighty.

Finally got my hands on my Mighty upgrade. As compared to the Crafty, IMO the Mighty wins hands-down. It heats up faster, charges much faster, and holds a much longer charge. The larger cooling chamber is more effective, and the temperature drops are much less severe, leading to noticeably...

Was supposed to get my Mighty today. Turns out they shipped to the wrong address - even though I handwrote on a piece of paper specifying the correct return address (I also shipped it from the address I wanted it sent back to). Somehow they put in my old address instead. I called my former...

As an update: S&B replied back via e-mail refunding me the 30 dollars and shipping via USPS priority mail. Glad they were able to remedy the problem. Looking forward to seeing if the Mighty will be any more reliable than the Crafty (I haven't read through the Mighty thread yet).

What the actual fuck - I can't believe S&B is cross-shipping now for some customers after telling me (two days ago!) that their policy was not to do cross-shipping. They couldn't even process my payment information for my Mighty upgrade until "after they had looked at it," I guess to confirm...

My third Crafty broke today... woke up this morning, tried to fire it up, was greeted with intermittent blinking red lights. Tried to plug it into charge and I get some weak green flashes, and then nothing. Sometimes I can connect to the vape via app, but I can't reset to factory settings (and...

I can't help but constantly be disappointed in S&B's customer service. They seem hellbent on making sure it's always at least two week delay to get my device. Last time it broke, it took them a really long time to turn around the device, and then shipped it USPS, which was reasonably fast...

Second Crafty unit looks like it's going to fail as well: it's been charging from 1/2 for about 4 hours now and according to the app is at 2/3rds of the way full. Emailed S&B but there's really no point, they're just going to tell me to wait until I get the signal and then to ship it back to...

I agree that plenty of non-defective cooling units get abv leaking in with the stock screen, but I don't know why people care. As long as you're not inhaling abv it's just being nitpicky. As for the fine screen - I just tried it with my new unit, and it's already pretty glazed. I agree it...

Got my Crafty back. Came during a busy workweek, so I have to let it sit for now, but I did notice some stuff off-hand. It looks like S&B is listening, and incorporating changes into the machine. For one, the smaller two o-rings are now red (the big two are still blue). Haven't played around...

Still no Crafty - despite any shred of optimism I had, my original estimates were true, and it will be a total of at least 2 weeks before I get my vaporizer back. I have yet to be able to talk to anyone on the phone, as their phone line is never operating (I get a message stating that the line...

The log says 145 but it's inaccurate - it leapt up a little bit ago from like 60 or so. There were a few signs that it might be about to die near the end, such as weird light glitches (normal mode would be a blinking light, boost would be a fast blinking light) and taking increasingly longer...

Damn. I've been working my way through this thread but jumped ahead to post: my Crafty died this morning. Got the red-yellow flashing light of death. Gonna have to send it back in I guess. This is going to be a lonely next two weeks :lol::(

Because my o-ring isn't sitting properly, I can't even leave them in - it just pops right off. I left the larger one in for several cleaning sessions but then it got so gunky that it was hard to handle it while cleaning so I pop it off periodically now. Left the largest o-ring in since I got it...

http://imgur.com/mPTzBo3 If you look closely, you can see the little notch in the middle of the o-ring. The notch is where the two prongs of the hologram piece fit into. The problem is still there even if I slide the hologram out and don't take it off - it pierces through the o-ring right...