Recent content by Phife

I tried wrapping my 28G clapton wire around my donut like that, wasnt able to cover it as much as I would like and the wire surface area was much lower than the design im using now. Were you not able to wrap the wire tighter to the donut? The wire on the outside isnt even touching the wick, you...

Yes, It was from my AC kit i got when it first came out. Impossible to find otherwise at this point. Ive been looking. If anyone one finds them please let us know!

Ive been doing the wrapped donut for about 3 weeks now. It works ok, Might go back to dual coil regular ceramic wick. I find the ceramic wicks do get "Full" of burnt oil after about 1g of shatter. I just do a burnoff by switching to power mode and pulsing the coil at around 30w for a few seconds...

This really is not the right thread to talk about Ejuice stuff. This is the One hitter quitter thread for Oil and not THC Ejuice. You'll have better luck asking these questions in the THC Ejuice thread...

A note to the people using the SX Mini M Class. The Dry Coil warning can be an issue if the coils resistance is on the higher range. It comes on when there is still oil on the wire and stops firing. it can also be hard to load. But I find it works perfectly when I keep my builds at or below...

Yeah, the coil holds some oil, Im sure some of the fancy specialty wires can hold even more, I just dont have the patience to make specialty wires. I was hoping that a Temp. Control device that can use Kanthal would come out soon so I can just buy the premade wire from Vapor Grudge and the like...

Here's my latest favorite build. I got a different version of the Veritas RDA that has more room in front of the hole. On the old verison I could only get 1 - 3mm white ceramic rod with a Nickel/Kanthal clapton coil on there. Now I got 2 - 3mm white ceramic rods and dual Nickel/Kanthal loose...

Cool, so just a coil and no wick? How does this hold the oil? wouldnt it just run right off the wire? How does the deck look after several uses?

Two more potential RDA's for Oil/Wax. Both have similar decks. Two posts spaced apart with lots of room in the center. Hobo V3 (Nice and Small, should be great flavor)- https://www.fasttech.com/products/2489000 Velocity RDA - https://www.fasttech.com/products/2482500

I dont have the dry coil warnings on my 350j unless the coil is actually dry. I did have to up the temperature to 250c to get it not keep saying dry coil. Perhaps you just need to up the temp? Or maybe your device works different than the 350j. That being said, I wish I would have waited too...

If you have a temperature probe or some way to measure the actual temperature of the coil you should check to see if its staying where its supposed to. I noticed on one of my builds on the vengeance RDA the coils wouldnt get hot at all and it would give me the dry coil warning. I had to up the...

Hey Guys, Sorry, no video. Maybe i'll make one up when I get my new Vertias RDA (slightly bigger version than the one I have) So far its been working good though, I should say I got my YiHi SXMini Mclass from Dash Vapes not from Fasttech, it was $249.99CAD. I got the Veritas RDA from fasttech...

Ive been experimenting with my new SXmini Mclass and a Veritas RDA from Fasttech. The Mclass has temp control which after some fiddling around with actually works really well. No more puddles of burnt oil at the bottom of my RDA's deck. When I am using my rig as a dab unit with a whip and bong I...

Got my SXmini M Class Yesterday, I dont have the Vengeance RDA yet, but I do have a Magma V2 which is nearly identical but the posts are closer together on the Magma V2 vs the Vengeance. I could only fit 2 coils on it with the 3mm white ceramic rods. The Rods touch the deck and the coils are 8...

Ordered a SX Mini M Class with temp control today, I also ordered some 28 and 30g Nickel wire. Also last week I ordered the Vengeance RDA from fasttech. I hope to be able to build a 4 vertical coil build on it using my FC2000 ceramic rod (4 rods, 4 coils, as close together as possible in the...