Recent content by Camouflet

The heater plates are visible inside the Camo caps and the Injector housing. The last heater plate in the stack is laser welded in place, so we do not want to attempt to remove the heater plates. Disassembly is not intended. Convector XL easy clean method for all components, together or...

Here's some Camouflet Banger highlights from Sneaky Pete's livestream. The Banger is a new and unique way to dab concentrates. When paired with the Inductor you can achieve a traditional torch dabbing experience in seconds with a flame-less setup & environment. With the added mass from the metal...

We've found that 550-600F with a 5-10 minute heat soak when pairing with and enail coil is ideal for darker roasts. You'll want to adjust temperature settings slightly according to your draw speed and the depth of the screen in the bowl you're using. A smooth/steady draw is recommended, if you'd...

The Camouflet heater matrix found in the Convector series and Injector is comprised of heater plates made of a specific stainless steel alloy that is optimal for induction heating compatibility. The heater plates have tiny holes throughout, creating a matrix design for the air to weave through...

Glad to hear you're enjoying the Convector! The standard Convector will fit all induction heaters on the market. The Convector XL cap has a 15mm diameter for reference.

All good, no need for apologies. What you're describing is not related to the threading/connection of the handle to the heater, but rather the tightness of the nut and bolt in the handle itself. The Camouflet Injector handle uses a nut and bolt system. To keep the handle in place, the nut needs...

Yes, there is a Injector thread in the plug-in vaporizer section - click here. This was the first production run of the Injector and the handle will see refinements as we progress. What issue did you hear about the "connection to the heater"? There are no known issues with the connection.

Convector XL and Wand: 10-12 blinks from cold start when used native. Less heat/blinks for subsequent reheats. 11-13 blinks from cold start when paired with glass. Remove the ceramic tube when pairing with glass for better airflow. Make sure the Wand batteries are fully charged for best results.

Once you become more comfortable with heating you can try adding some heat to the side walls of the the Camo cap/chamber as well. This will preheat the chamber and result in more heat retention = less heat calories lost to the cold chamber. Do 1x full pass around the circumference of the...

We're wishing everyone a Happy & Safe 420! To celebrate we are offering a free Convector Titanium Factory Seconds on all orders over $50! 🙌 *Offer is for this weekend only. No codes required and you don't need to add the free Convector to your cart. We will add it automatically to all orders...

Happy 420 everyone! New Zooter & Inductor video for your enjoyment. "Life moves pretty fast. If you don't stop and look around once in a while, you could miss it."

Happy Friday and almost 420 everyone! Tune-in to Sneaky Pete's Inductor live stream today and join the session! Friday April 19th 2pm PST. :popcorn:

Without knowing all the variables of your Convector XL ritual, our guess is that you're over-packing the chamber and/or the material is packed too tightly in the chamber. Start with a medium/coarse grind instead of a fine grind. Material with a good amount of moisture is best vs dry/crumbly...

Hello @Nobo, Camouflet Tech Support here, In case the retailer did not forward you the message, this is what we sent last Saturday: We have not seen a reply from the retailer yet, so we suspect you did not get it. We have never seen or experienced an issue where the power supply would only...

Hello, we replied to the email sent by the retailer you purchased from on the day we received the email. SAT APR 13 12:54 PM. If the retailer has still not replied to you this is outside of our control. We do not conduct customer service on FC or any other forum/platform. Please email us...