Discontinued The Persei Vaporizer for herbs and concentrates.

[MaxVapor]

on a side note.

Pure ceramic bowl. for your persei dun dun dunnnnnnnn.

Hmmm, Hercules technology mark II... so perhaps you have figured out how to make a disk using the same tech as the rod (is there a wire in the rod?). Or wire embedded in the disk like a fancy electric range. Top half is for water?

 

[THC SCIENTIFIC]

Hmmm, Hercules technology mark II... so perhaps you have figured out how to make a disk using the same tech as the rod (is there a wire in the rod?). Or wire embedded in the disk like a fancy electric range. Top half is for water?

Not telling anything. But the inside shows a lot more design then i am willing to show ATM.

I mean the technology we are developing is ahead by leaps and bounds compared anyone in our field. That is why I hate wire heaters. They are old tech. Why not develop the future and just let go of the past.

 

[ohdono]

Can you please try it the Hercules without the middle PTFE piece, just use the top stainless cap and the mouth piece like this photo.

I know everyone is trying to help but please follow my diagnostic instructions and we will get it working.

*finally got home to reply*
i tried and its not much vapor from how much wax i put in. fully charged batteries it takes my persei until it goes lights out for a single hold on the persei for the rod to get red. and takes another full hold for it to start seeing vape. here are pictures of how much i loaded.

 

[THC SCIENTIFIC]

Do you have the top stainless cap? And can I see your mouth piece from the stainless screen side.

 

[MaxVapor]

Not telling anything. But the inside shows a lot more design then in willing to show ATM.

Lips are sealed ay? Well that's good since loose lips sink ships as they say. I am sure what is in there will be worth the wait.

On another note, I really like the Kiss cart.

I know it don't hold a candle to the Herc in my closet, but for my typical use case it's great. I have put sticky wax, crumbly wax, shatter, and co2 oil through it. All in very small quantities. All vaped beautifully. Small quantities is where it shines. No .5g "buffer" to load, just drop a bit on the coil and you have lungs full of vapor 3 seconds later. Lots of vapor. Because basically I am lazy and busy (which is a terrible combination) I usually only have one 2.4 cart and some pure gold going at a time. So I don't get much variety even though my cupboard has a nice selection that I have been acquiring over time. Yeah, I could load a couple more 2.4's and have them around, but that is more labor. Plus none of my labeling schemes have seemed to pan out and I always forget what's in what cart. And if I ignore a cart too long it seems to be more prone to leaking/clogging.

Using the Kiss I have been loading a tiny amount, maybe .025g. Start inhaling, hold the button 3-4 seconds, then 2 second pulses on and off until at lung capacity. That will vape most of the load. Repeat a little while later depending on how big the rip was. After several loads enough will have built up under the coil to get a "free" hit. I hold the Persei horizontal and give it a 3 second warm up without inhaling, then give it 3 second on, 2 second off pulses. This gets the residual oil to flow up along the side moving closer to the coil and eventually vaping mostly off.

Then I'll give it a few quick pulses to clean off the coil and it's ready for a fresh tasty hit. So far the flavor has remained great, specially on the first hit when the coil is clean, not so great when you get around to the "free" hit.

Kiss makes it easy to sample a wide variety in a short timespan. Which is what I have been doing this evening. Sleepy time is coming on fast.

 

[ohdono]

Do you have the top stainless cap? And can I see your mouth piece from the stainless screen side.

is this what you mean?

 

[THC SCIENTIFIC]

Can you take that stainless cap off I want to see last pic without the stainless top cap.

 

[ohdono]

 

[THC SCIENTIFIC]

@ohdono

ok now my question, do you use the stainless top cap with or without that PTFE nut that holds the screen in place?

 

[ohdono]

@ohdono

ok now my question, do you use the stainless top cap with or without that PTFE nut that holds the screen in place?

with the but that holds it into place

 

[ohdono]

any ideas ?

 

[THC SCIENTIFIC]

any ideas ?

It's the air flow or not enough in there. Only way that pics you showed of the coils they look empty and the amount you put inside looks like not enough.

Ok few more questions.

Do you install the stainless cap first then then mouth piece?

 

[exit]

any ideas ?

be patient you will be helped in due time..... not everyone's always at the pc

much appreciating the lil review @MaxVapor you're saying just what i want to hear.

now then..... can you load up a KISS with enough to let you hit for 15-20 minutes straight? or does it need reloading in that time? because i definitely see where it'll fit into my lineup. now i just need to decide if to go 2.4 or 2.4 and 5 ohm.....

 

[ohdono]

It's the air flow or not enough in there. Only way that pics you showed of the coils they look empty and the amount you put inside looks like not enough.

Ok few more questions.

Do you install the stainless cap first then then mouth piece?

I install the stainless cap that fits in to the ptfe nut to the mouth piece then put it on the herc. what I melted into the cool was atleast .6 or .7 gram and I'm receiving nothing close to clouds

 

[THC SCIENTIFIC]

I install the stainless cap that fits in to the ptfe nut to the mouth piece then put it on the herc. what I melted into the cool was atleast .6 or .7 gram and I'm receiving nothing close to clouds

Ok take the ptfe shell off use it without the shell tell me how that goes. And also did you weigh what you put inside?

 

[THC SCIENTIFIC]

I mean did you use it in this configuration ?

 

[ohdono]

Ok take the ptfe shell off use it without the shell tell me how that goes. And also did you weigh what you put inside?

gonna get back to you trmw morning have to get some sleep thanks for the constant active help really means a lot to me I'll update you guys trmw

*edit
I'll weigh atleast .6g when I test it trmw.. should the rod even take that long to turn red hot ? it takes until you can't hold the power button any longer

 

[Rhino420]

*finally got home to reply*
i tried and its not much vapor from how much wax i put in. fully charged batteries it takes my persei until it goes lights out for a single hold on the persei for the rod to get red. and takes another full hold for it to start seeing vape. here are pictures of how much i loaded.

looks like a brand new, un cut coil from the pics... also looks like there might not have been a buffer prior to these pics?

if so I would try cutting the coil down...

 

[ohdono]

I mean did you use it in this configuration ?

yes I did

 

[ohdono]

looks like a brand new, un cut coil from the pics... also looks like there might not have been a buffer prior to these pics?

if so I would try cutting the coil down...

it is a cut cool of 40% and there is already melted wax below what I show on top that is on the cool in the pictures

Ok take the ptfe shell off use it without the shell tell me how that goes. And also did you weigh what you put inside?

I didn't use the ptfe shell like in the picture you provided, I have it exactly the same. I have the ptfe nut in the stainless top.

 

[Rhino420]

it is a cut cool of 40% and there is already melted wax below what I show on top that is on the cool in the pictures

if that's a 40% cut coil, then your coil is not sitting all the way down in the herc, my 40% coil, sits a little below the ceramic rod...

if the coil is not all the way down it wont hit right...

just shooting ideas out there, trying to help, good luck

also, I put the uncut side of the coil facing down, just because I feel like it will sit more flush at the bottom of the herc cart...

 

[exit]

Loaded two 5 ohms to tide me over until Herc gets back

Forgot how hard these babies kick in a dual configuration! Damn!

 

[exit]

@THC SCIENTIFIC i have one more mystery for you, hehehe.....

on my dual cart head (which i never ever used with the herc) i am noticing the button seems not to be as sensitive, and sometimes it acts up.


occasionally it gets stuck in a loop where if i press it, the light flashes and goes back off. this will continue unless i physcally unscrew it remove it and put it back on.

then it'll work fine if i jam the button in really hard, but once in a while will give me the "Battery low" flash, even though i have two sets of 100% fresh off the charger 18350;s to try these with.

take your time getting back on this one, it's at the bottom of the priority list!!!

 

[Rhino420]

@THC SCIENTIFIC

I was thinking of trying a kiss cart with my persei...

question #1 is, are the old tops not designed to handle these new kiss carts, like the new SR-71's?

I have an old persei, with old tops. so I have no warranty. I run a SR-71 with the white and black rods, with no problems... but I also know how to check to see if I assembled the herc correctly.

question #2 is, is there a way to meter these carts to make sure not to fry my old top, because I would really like to prevent myself from trying one of these kiss carts, without worrying about purchasing an upgraded warranty for my persei.

TIA

-ryan

 

[exit]

I wonder if anyone else feels this way.

Having been withuot a reliable sr71 for a few days I decided to dig into my cart collection and fill a pair of
5 ohmers. The behavior of them is extremely similar to how one would act in response to the SR71 getting hot enough to keep putting out hits. I keep finding myself trying to do other herc tricks wiht it (oops, can't relight it, that'll burn it out..... oops almost pulled too hard)