Search results

The one-hitter is now perfect with the longer “more gap” test tube. The cap holder has been slightly modified. Now it is out of the heat. With a little twist, you can grab the heater at the bottom with your fingers to remove and reload it. Unwind the upper spiral to get it back on. It stays...

Yes. As @Radwin Bodnic said... DIY. Its just a stainless steel tie I wrapped around to secure the cap and adjust the immersion depth .

Just for science... ;) ... tried it once more. The ar-glas gets pretty quick reddish with a three-flame. Three to four heats or reheats with looong draws gets me there. it all cools down pretty quick to get it back in the pocket. .

Oh. I am amazed. I actually use it in the same way as the Vaphit QOQ. Heat the glass until it starts to shimmer slightly reddish. Just the upper part, where your bowl is. The draw resistance on my construction is quite harsh. Not unpleasant, but not free flow either. I have to admit, I've just...

Oh wow. K.I.S. In my case the "heater" is ar-glas with flat bottom. It gets hot too. ;). EU: https://www.amazon.de/dp/B07BK2ZKZ8?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_2&th=1

Hi folks. by chance I came across unklmark's (RBT) page on Instagram. Looking at the beautiful pictures, I thought to myself, what a shame that I wasn't into wood back then, I thought glass and stainless steel were better. This woodwork is simply a feast for the eyes. Now they are OutOfStock...

Hi. If someone is still looking... they have them in stock. (GER, EU ...maybe WorldWide) https://verdampftnochmal.de/mad-heaters-tempest_3 and while reading through the reviews Thomas L. (Thanks!) pointed me to a trick/feature about the Reload Gen 2. Just open the 2 screws and turn the magnet...

The onepiece-bamboo-biro is the key. 4€, Ebay. Sits perfect. ;) No destruction. You can reuse the biro... will be the best smelling biro on earth.

Yep, you can work with that piece. Disassembling was easier than i thought. No glue! Raw wood on the inside. On the sides where there is no groove... the tempest sits tight. Daynavap also. Even with the slit it works perfect with a 14mm female. Happy tinkering. ;)...

Lets make it the forum-biro, bulkorder, "fuckcombustion" laserengraving. ... OK lets take it apart... just wait for some pics. ;)

Hi. Long story short: Bamboo-Biro Stem/Vong (IMGUR) The Tempest wobbles a little with standard o-rings. But it is OK. Dynavap sits tighter. You can see they grooved the part inside... good for the Vapcap, bad for the thicker Tempest (i am thinking of the ring after the o-ring part). The inner...

My best tip so far: heat up to the second click and maybe 1 or 2 seconds longer. A direct hit without a bypass. Loose packed, full bowl. And in my opinion, that should actually make everyone happy. And i think it would be cool if someone has difficulties, let us know how you heat (jetflame...

...at the bottom of the drawer... where there are more... so that's how it should have tasted “back then”. Now I'm super-happy.

Delivered today. What a beautiful piece. Thanks.

So sorry... i thought it was 11 AM ... meBad. Thanks for clearing that.

...The drop is unfortunately already over, it was this morning, 11:00, after European time

Hello...It's quiet here. Let's talk about the topic. In the meantime, I've taken on an old cherry tree that has been with me for almost my whole life. We cut it down five years ago. I stored the trunk upright during that time. The wood is a disaster, rotten and worm-eaten. But I was able to save...

;) ... thats the way to ski! :rockon:

Your point of view is a good one. You know, I'm just thinking about how much my self-built vape might cost. It's like a terpcicle with a coil and a wooden heat shield. Handmade. (look under the DIY section). The PID is modified and equipped with an SSR, built into the PID-housing. 3d-print...

If you stick to DNA Mods you can use the Escribe Suite to save your actual "firmware" and can flash Lamarts. Look on his site for some instructions. Some info is in the BAKx manual. You need a mac/pc. Your Hadron need the BAKx material file.