Search results

My digital vernier says...26.81 at the fattest point and a bee's dick less where the vapor hole is.:tup:

Welcome to the forum, I might be biased but the Roffu sounds like it will suit your needs, you could add a WPA and capsules and come in well under your budget, https://xvapeusa.com/product/xlux-series-roffu-powered-by-xvape/ https://fuckcombustion.com/threads/xvape-xlux-roffu.52284/page-90

Sorry for the late reply, I was out bush for the weekend. I have not heard of the off-gassing problem with the Starry4 before and a lot of peeps like and use the vape for concentrates due to its high max temp with no problems, that said, I have forwarded the info to my boss at head office and...

It takes a lot of effort to scratch, I only have scratches on one of my 3 units and that was due to tripping over and literally throwing it against a brick wall for it to finally land on concrete. I have used the case and it works well especially when on high temp with back to back sessions on...

I got this kit BG020, handy for some jobs but not every job I needed...

I use the following set up for mating my Roffu to a J-hook etc,

If you cannot get from USA for any reason, for capsules, the XMAX V3Pro capsules will fit the Roffu...

If you ever get a tube of 5x capsules, that tube holder is the exact fit for the Roffu heater. OD=11.94mm, ID=11.15mm, L=23.54mm, wall thickness=0.44mm....the measurements were done with my digital multimeter on an old slightly mangled metal oven. That said, the paper rolled into a tube is an...

I would say that is the opposite to what I was describing, conduction from added mass via a dosing capsule seems to add sleepy/relaxed to the mix. If you want alert/get up and go then convection would probably suit best (I like low temp Roffu glass bowls) or even rosin dabs, my preferred 'during...

Not as 'stoney' but much cleaner. You can get a bit more of a stoney effect (helps with sleep in my case) by using stainless steel dosing capsules (in most vapes) as the added mass retains heat as your session goes and can help bake the herbs for you.

I have had my 3DXL for about a year, if there is a newer version, am I missing out on something? I do like the sound of the bottom being heated on the 5DXL and may get one to replace my 3D chamber on my older V1 Peak Pro as I am also looking at another travel kit from JCVAP...

I get these cop lights every now and again and the simple fix is to pry out (just a tiny bit) the gold pins on the bottom of the atty and it always fixes the fault for me...so far with 4000 dabs on 2 different units.:tup:

I have been looking for a decent j-hook to mate with my Roffu since breaking my old favourite. There are so many variants available but none were the same as my OG...until now! The following is available in 14 or 18mm and is a bit larger than all the others I have tried (which is good for me)...

The first couple of drips that come off certain strains are nearly always lighter in colour than the rest of the press if you separate them, this is with cured buds, not bubble that I have seen...your product looks beautiful by the way.:tup:

I translated to English so you may get more answers:tup:, Good evening, I have a problem with my pid controller that I am going to buy with the phase 3zx it lowers the temperature instead of raising it maybe someone has a solution or maybe a pid manual to share to try a different configuration...

I have been pressing with my 10t Dabpress for just over 6 years and it is great, driptech sure does preserve extra terps by getting the rosin off the plates more quickly. I can also grab the first couple of drips in the first 30 seconds to 1 minute of the press (a press can take 2-5 minutes...

Gunna need a bigger boat,

That is great advice, it is also pretty easy to combust if you try to squeeze too much out of a single load by running back-to-back cycles.

Or a vacuum cleaner may help...I find sunlight and time can also finish curing anything I may smell.

They look a bit different when you look closely, 2x cage guides on NArra compared to 4 on the Graveda was the main difference followed by the Graveda has a fully enclosed PID controller and the NArra says heating plate when pointing at the lower plate so not sure if the top plate is heated as...