Search results

Well, no one said it should be accepted. And if you peruse my postings in this Vapvana thread, you'll note I'm rather critical of their rush to push out products that aren't 100% there yet. My point is the lack of CS interactions regarding the ACE bowl isn't because most function properly...

No reports because most people, including myself, wouldn't contact their CS about it being it's mostly a non issue. But for the record, mine always pops out when it's fully clean. Learned that the hard way the first time I used it and literally dumped my abv and screen right into the garbage...

I'm not sure they'd have anything to say. As jaanky mentioned there's no groove in the all glass bowl for the screen to lock into. It just sits on a small ledge. While I don't have the full Ace set up, I do have the all glass bowl. My experience is that once you use it a few times a very thin...

The O-Rings bleed green stuff when exposed to the common solvent used to clean vaporizers and their parts. The manufacturer sent replacements. The replacements also bleed green stuff when exposed to the same common solvent. I'm not sure why speaking about this fact bothers you so much? Have you...

ISO is likely the most common solvent used to clean vaporizers. People are absolutely going to use it to clean these bowls, period. The issue isn't swabbing the O-Rings. It's the fact that they bleed green "stuff" when exposed to ISO. And then the question becomes when they bleed this "stuff" is...

You don't need to soak anything. Dip a Q-tip in iso, swab the O-Rings right where they sit in the bowl. They will bleed green right onto the Q-tip. My originals did. My replacements did as well.

Yup, rotating between the all Ti and all glass now. Not going to bother pursuing anything further with the hybrids myself. I'm over it, and the other two bowls work better for me.

So my new O-Rings bleed just as much green when swabbed with 99% iso as the previous ones did. I'm over these hybrid bowls.

I've seen glass artists use a Ti "pen" to sign their work on the glass. I assume it's likely impossible to have a sharp angle made of Ti which interfaces with glass that doesn't leave Ti on the glass in some way.

I received new bowls as well as extra O-Rings in the packages. The O-Rings that were installed in the new bowls, as well as the extra one's I received, were the same exact green. I don't know about any tolerance changes, haven't heard anything about that.

I do own one, but have only used it on a limited basis because I have a few issues with it's functionality. They're my own issues, but they still prevent me from using it daily. The first being my daily driver bubbler has an 18mm joint. So to use the Ace bowl, which has a 14mm joint, I have to...

So I feel the same way as VapingYogi regarding the hybrid bowl's performance compared to the all Ti bowl I feel like you get better conduction and even heating with the all Ti bowl.

Here's a new one. After removing the stuck glass in my hybrid bowl I decided to swab it out with a Q-tip and 99% iso. Those green O-rings bled green all over the iso soaked Q-tips. :\ Not sure what that means, but not thinking it's a good thing. I'm back to using my all Ti bowl for now.

My hybrid bowl adapters were easily removable at first, just required a firm grip and twist. Then after a few weeks of use I cleaned both bowls. All of a sudden the glass adapters no longer went in easy or came out easy. Currently the only way they're able to be moved in and out (without fear of...

So as I'd mentioned, I've only had them on hand for about a week. But they are indeed super tight, especially after using non stop though the weekend. I noticed wiggling doesn't work well, neither does attempting to pull them straight out. But here's what I've been doing that seems to work...

Anyone else receive their hybrid bowls yet? Mine came in right before the weekend. Loving them so far. Super easy to swap the glass out. And I'm especially stoked to be able to use my 14mm pieces again. Also, the microdose bowl is a really good size for solo sessions. Another cool side effect...

Late to the game here, sorry about that. But fwiw, I stretched and tightened the coil on my B1 and was able to run it about 50 degrees lower than I'd been using it previously. Did exactly what's described in the post above. Used pliers to tighten it as well. Very simple procedure. Though I did...

Indeed I do. I was actually surprised to see some activity in here from the past few months. I really enjoyed the few Hammers I owned. Shame there's no support for them anymore. Bit of a persnickety design, but so effective once you get the hang. I was super lucky that @VAPEHUNTER was nice...

Haven't been around in a while! How's it going? I have quite a few stems hanging around from E-Nano's, Underdogs, as well as Heat Islands. Unfortunately none seem to fit the Hammer Pro with or without the silicone sleeve that the Hammer Pro added to allow the stem an airtight seal. Thanks for...

Long shot question... any one know where to find replacement stems that fit these units (Hammer Pro)? Located my unit in it's box while cleaning out a chest of sheveled vapes. And after years of not touching it, it fired right up! I was fairly shocked. But I have no stems. Would love to get it...