Search results

This sounds interesting, a picture would be nice but not easy to do for some.:tup:

I am in the same boat (except my glass is fine). I find I am using the OG MP quite often as it cools so well and fits in a pocket much more easily. Keep us informed of your progress, please.:tup:

Zee's has them on sale often and are great to deal with, https://www.zeevapor.com/product-category/focus-v-carta-device/

It does go away(the new car smell), as far as the irritation, that may be you. Have you ever used a vape with a Kanthal heater? Some people are sensitive to Kanthal, rare but it is a thing. I would try again but keep your temps below 190C/375f and do not pack the bowl, just sprinkle fill as...

Not just you, I would rather finger-pick than use one of them.:tup:

Mine cost $2 to be able to open up my Plenty, that said, go to an electronics repair shop @ruint.:tup:

As it is a grinder for life and if you don't want to buy the medium plate later, I would wait for the medium or pay a little extra to get it now.

If you want a large BCG you have to go aluminium...my large medium plate aluminium BCG is great and gets used equally with my OMD S/S...the large BCG is better at bigger buds IMO.:tup:

Just in case you could not see @Pishorkata 'SPOILER' from the last page (like me), That is great going @Pishorkata, makes my 8000-odd (OG unit) puffs look like a noob.:tup: A few units from the OG batch would do a partial heat-up whenever the battery was swapped or when the charging cable was...

Good to see you got your unit just fine @Reez79.:tup: These guys are legit and recommended battery for any vape, https://www.18650batterystore.com/en-au/products/molicel-p28a I had and XTAR charger but that died and now I have a Nitecore SC4 that works a treat and lets you know when the...

Thanks for answering with great WPA advice @vapviking, I could not find what @Philossifer was talking about from those long links (I never saw the pics). I have found I have been using the Roffu silicon WPA with the glass as it seals nicely in a 14mm dodgy ground joint water pipe I have (I also...

https://rcctools.com/heat-coil-pin-wiring/ Easy to reconfigure if needed.

Not sending a replacement until you give Oz the Ashes Urn.:lol: But seriously, now I know you have a problem I will chase it up for you...PM sent.

Mine survived the ultrasonic cleaner just fine.:tup: I like it so much I now have these on order, Model C, https://www.dhgate.com/product/y149-hookah-smoking-pipe-3-models-glass-hammer/869510639.html?dspm=pcen.orderlistpage.astab.1.0u89kpdfFilSxbU1fRDT&resource_id= And I liked the conical...

Yes, most smaller convection-oriented portable devices do. It is convection orientated but the unit will heat soak the chamber and whole device eventually As stated, the device is convection heavy, the more hot air you pull thru the load the more steam and the reason I like a medium to coarse...

Thanks @Bad Dog for the hammer recommendation. I have been using it today with great results (the mouthpiece pinch does not restrict at all). I find it works very well with my Roffu that is usually a bit restricted feeling for larger water pipes and the reason I usually run 2...not needed...

The sale will not show on your account as it was created after your purchase, if you are stressed at all, call the office again during business hours to get more reassurance if needed.:tup:

I forgot to hit the reply button on my response yesterday so thanks for the tip about the oil cart @Petetbay. As far as cleaning the tip, I do the same as with my other fritted quartz and simply soak them in iso in a plastic test tube (suspended in an ultrasonic cleaner away from the transducer...

My mode of operation is to use the capsule lightly packed, turn on the unit and wait for the pre heat cycle to run then draw. I get 3 or 4 long draws in the session time with lots of vapor(and is spent for my liking). If you are getting little vapor I would say your unit is faulty as all of mine...