Search results

Because for me it has more to do with airflow! the glass honey comb screens do not have as good of airflow as the ti bowls.

Ok so I did some testing today for science of course. Maybe my mail order mary just came in lol. Anyway back to science. The first hit was at 825f uncapped with about a 0.25g bowl. The second hit is at 845f capped with 0.1g in the bowl. I was enjoying some black cherry punch and jelly breath.

Well as far as high temps go the highest I have tried is 825f capped at the start. Milks up very fast and very easy to combust. Just half a sec of cap then a medium to fast draw will leave your bud black but not white.

Wow that is the lowest temp I have seen for cumbustion! Recently I have been flying high at 800f on my showerhead. Very fast draws.

I remember someone blabbing about the handle breaking on the bowl. This however it is not true from my understanding. I wack the handle all the time on glass to empty the bowl and its still good.

I would recommend searching the thread for this as it is a very common topic here. But from my readings its pretty much been summed up into this. The flowerpot is only better at one thing and that is the high temp fast draw hits with no carb cap. 747-777f. Other than that you can adjust your...

@TheFatBastard I too switched from the tower to the flowerpot and was not blown away at first. The thing that blowed me away though was fast one hit full extractions with huge rips. The v tower was slow and took a while to finish off the bowl. Take three hits outta the flowerpot at 777 with...

If you are looking at the flowerpot then I would say most of the units are pretty much the same. I think they have made some slight changes but as long as you get one that was made in the past year and a half you will be good. The auber controller is the better one that people seem to be using...

i ended up putting a bit of electrical tape around where the shim meets the braided cable cover cause that was the problem with mine. The shim would fall off the cable housing then it would be all loose. I think it has to do with me constantly packing the enail up and stuff lol.

Hey guys I was wondering if its safe to ground my cable/secure the enail handle in the unit with some electrical tape? Every so often It comes loose and i have to take off all the hemp wick and re put it together and its quite a pain. would electrical tape be safe in there? thanks for your help...

great for flavor. not as great for airflow

I would just say if you get bored. then give it a break one weekend then try again the next. I use to be a daily user pretty much all day long. But now I vape 2-3 days or evenings a week. And I find my tolerance is super low now. If it goes up a bit I just take a break for a couple extra days or...

good to know although just so you know there is no fluoride where I am from! There is no build up of anything on the dab surface so I think I should be good. Unit cleaned up pretty good actually. May give it another once over tomo. Again thanks for the help guys.

I guess my only question is if its minerals? its not gonna be unsafe or effect anything to much right?

It may be honestly My head has touched Water. I always make sure to Iso it after but its possible. I am from BC though so we have probably the cleanest tap water in the world.

I have found the previous guys solution. His looked alot worse than mine and was on top and he used dish soap and hot water to get it off. I am a little worried about using dish soap though as I do not want any to bind to my Dab surface or something. @NewVape710 @newvape918 do you guys have any...

It has never been past 777f. Never been torched. However until recently it was turned on for a very long time without turning it off so that may be the case. I was kind of a slave to the thc so it never turned off. But now after my break it is only on a few times a week.

Mainly the showerhead piece on top of my unit has this awful looking white film on it:(:(:(. Idk what it is or where it came from but 99%ISO does not do anything. Does anyone else have this or have any recommendations on how to get it off? https://imgur.com/yK44zZh

I was just wondering the composition. Want to know if it is tested for high amounts of nickel or aluminum. As well as what series it is.

I was wondering if you have the info on the SS that you use @Ed's TnT I was wondering if it was certified to not contain any *EDIT high amounts of Nickel?