Search results

@cybrguy thanks a lot for video. I'm doing same way last couple weeks, but sometimes it's not so easy because of friction between M's mouthpiece and ring finger (that's why in case of upgrade I want spinning mouthpiece instead of omni, also like to use carb hole different ways depending on temp...

@beyond6strings sry, can't make video, but I measured with timer few times and got 2 clicks at around 30 sec when heating mid and 40 sec when heating bot, it was earlier when I rotated VapCap fast back and forth. Later I changed method to rotating slower in one way + squeezed cap to get more...

@MaalboroMan thanks, gonna try smaller flame and faster spinning. First time I tried to spin it forward and backward when heating, but I couldn't make full turn without fear to drop it especially when already high, so I started to spin it one side and not fast (as recommended George in one of...

Honor single torch, flame length 2.5-3 cm to invisible part tip.

I usually keep it inside that invisible flame, 2-3 mm from the tip of visible flame. Gonna try to keep it further away next time.

I have VapCap M'18 for 3 weeks, usually microdosing with it and using like one-hitter - heat bottom (sometimes really long, around 40-50 sec) and pull with closed carb until click, my AVB was almost black but no combustion. Last few days I combusted 2 times when was heating as usual, and now I...

I'm really satisfied with extraction strength at max temp (220 C), it's almost the same as in VapCap M when heating cap's bottom with single torch (in VapCap AVB is a bit more dark almost black, I think it hits close to 230 C). Battery is ok, 11-12 4min sessions at max temp, if it would be my...

Finally got my Fog from PuffItUp, I didn't disassemble it but they told it's new version with safe insulation material. Also it's great for microdosing:

Looks like I don't need TI tip, this screen mod is awesome: http://fuckcombustion.com/threads/best-of-dynavap-vapcap.24345/page-2#post-1216849 I think it's even better for microdosing than TI, SS heat retaining + grinded fully loaded small pack = bowl can be done in 1 long hit. Also can be used...

Gonna buy M 2018 + TI tip. Main reason is microdosing (0.01-0.02 g) through adjustable bowl, but saw few posts where people were talking about "loose" CCD in top groove, how common this issue is? Fast heat up time is also nice bonus, but some people say difference is small, other that it's big...

Sounds bad... Maybe static charge killed controller, just broken wire that can be easily fixed or even short circuit of temperature sensor on metal surface (dunno where it placed) in this case it's resistance will be zero and controller thinks that temperature is very high (400+C if common NTC...

Anyone had this kind of issue? What it can be, broken heater, blown up transistor or controller problem? (people in comments describe same issue) Just choosing between Fog, Starry, FM v5 Nano and don't want it to be dead after couple of weeks...

>magnesium oxide powder Sounds OK for me, according to NFPA 704 health hazard level is 1, it's used in food industry as additive E530 and in medicine against increased acidity of the stomach. Also it's amount so small compared to asbestos dust and other shit I was inhaling during apartment...

https://twitter.com/VapoShop/status/965562364513935361 >Estimated shipping date: mid April

There are some new photos of nano on this shop site: https://verdampftnochmal.de/products/en/Flowermate-V5-Nano

Thanks, gonna watch it.

How do you think guys, is it possible to rebuild full metal drip with temperature control box mod into on demand convection vaporizer for micro tokes with minimum changes? I want to keep it small and without glass parts. It can be model with wide drip tip for a bowl with inserting into/above it...

Woah, that's really nice.

Is this vape's efficiency good enough for microdosing? Can It evenly extract something like half of an arizer air stem bowl? Can I use it like on-demand vapes - make a hit, turn it off, make another hit later and so on, will it overcook weed while turned off because of conduction part of the...

https://flowermate.com/product/v5-nano/ >COMING SOON: 01/24/2018 Can't wait for review and tear down photos...