Search results

Thanks for the update. Now, if we never hear from you again, we'll know why....... OF

Not advised, the unit is not designed for it and PIU's 'teardown' was destructive: https://blog.puffitup.com/2018/01/fury-2-teardown-new-year-new-vape-destruction/ And, of course, it blows your warranty big time. You might try a warranty replacement with HR, or take advantage of their half...

Your call, of course, but you might try a few drops of detergent in that 'just water'. It helps the process two ways, first it helps the solution 'whet' the surface of the contamination ('oil and water don't mix'....). Improving the contact there improves the transfer of energy and therefore...

You still haven't answered either of my questions: How much more are you willing to pay for this? Where do you draw the line? Do we need a service center in Switzerland? Monaco? I get you wish it was different, but the rules were in place before you bought into the deal? BTW, from a legal...

Don't set yourself up for a 'mind trap' troubleshooting here. Removing the airpath is a useful test at one level but it doesn't point to a 'fix'. Simply removing it allows air to rush in the port on the MP, no matter what's going on below that. If the airpath and MP both draw freely, the...

Easy enough to do for sure. HR had just used "Q-ti"', which I quoted, a more accurate (even if whimsical) term seemed in order? For sure saying 'cotton swab' would have caused confusion as well? We tend to get sloppy, using brand names when we don't mean that specific thing. We say 'Hoover'...

How much extra are you willing to pay for this? Should we include little markets, like say the Swiss (different from other EU countries, we'll need to include them.......)? It's, of course, a marketing decision. 'Above my pay grade' as they say. The Capitalist in me says if it's that...

No. Cotton bud is the correct name in British English (what most of the world uses.....) for what we call 'Q-tips' (which is a registered brand name, like crescent wrench). The correct American English terms is 'cotton swab' which wouldn't make sense either...

Yep, that's my advice......and the makers? And rinse/dry promptly. OF

You mean these instructions? Separate the O-ring from the screen and soak them both in ISO alcohol. After soaking - brush them using ISO alcohol - then rinse with water. Dampen a Q-tip with ISO alcohol and swipe out the chamber & glass mouthpiece. Repeat as necessary. Do NOT drip any ISO or any...

Plenty powerful for me, I'm a sipper basically OK with Fury 2. Fierce is more than needed so I usually use your 'two screen' technique (with reduced loads). I can see how Cloud Chasers might be able to overrun the heater, but not an issue with me. Shouldn't this be asked on the FIERCE thread? OF

You're welcome, good luck with it. Also, IMO, worth having an eatable fall back. I find a 1/30 of a gram (say 35mg) of THC is a solid dose for six hours, but needs an hour or so to be made available in your blood at useful levels. If I eat half a cookie it's in full effect before the...

Heat can, of course, be a problem. But really there's very little heat energy (calories, not degrees) in gases (including vapor in our case). Simply sipping on water or, better still, fruit juice, between hits can help a lot in times of need. The bigger problem over time is the fact the...

Do not soak the plastic parts in ISO, it will casue white residue....... And eventually ruin the plastic. Quick wipes only (then dry immediately). Yes, i KNOW (since I've done both solvents and detergents) a good wash in PBW will do better. As will a ride through the dishwasher for that...

Again, two different systems. Don't get fooled by the connector. The rub is in timing. Just because the sending computer is ready doesn't mean the receiving one is, and will keep up through the transfer. The communication is 'serial' that is one bit at a time on a single channel. Normally...

Not really, it depends.......... Then again, doesn't it always? Just because it's a USB connector doesn't mean all the required USB hardware is there. It doesn't have to be USB compatible WRT data while still able to use the power connections to recharge. I play around with a family of...

Me too, 390F is my 'default'. Not that it doesn't apply equally here (or on either Solo I or II threads) but if this is really about Air II shouldn't it be on that thread? http://fuckcombustion.com/threads/arizer-air-ii.25187/ OF

No. Not as you expect. For openers, there are no real/honest 3500s out there. Once again, advertising is ahead of state of the art...... There's a fellow with a screen name 'batterymooch' or some such who covers this in great detail, testing to confirm what really happens. For instance...

Not priceless......please remember your current gratitude when you get my bill...... In a rare (rarer of late) serious moment, thanks very much for the compliment. Glad to help when I can. No need for everyone to repeat my foul ups. I'm far from alone in that around here, as you may have...

Dollars to doughnuts it's a jammed 'up' switch. If you hold that button down, that's what happens (climbs to the top and ignores the big button. A common fault in computer controlled stuff. Most software 'reads' both the make (down) and break (up) of keys (which is why you can hit and hold...