Search results

MinnBobber, it does have to be held on, but it's a push-in. You don't have to bend your thumb and hold it down. It just sits in your hand, (whichever hand you want), and you push the button. The notch is about an inch,(or 25.4mm), wide at the top and is 1/2" deep. As you spin the cap it stays...

Shieldsab, I lost the sight in my right eye a while back, so losing 3-D and my depth perception it makes it a little hard to know where the flame is. To compensate I made a little aluminium fork that holds my vc in the flame. I just have to pay attention to how far into the flame I place it. I...

Pipes is there a magnet in my Jarhead? If so it's under the works on the lid. I do not want to take the works off the lid to get it. I can feel a slight pull on the cap in the center of the lid on top. Did a magnet get jostled to the center of the lid under the works? Doc

I still think these should come with Sergeant stripes. I put them on mine."Hoorah, Semper Fi." Doc

Two bi-metal disks in cap. One is redundant. In case you missed it. Use second click. For less vapor use the first one. If you look at the cap the side of the cap opening the side that has the digger wants to flatten out. To tighten the cap, make it rounder or less round . All the caps are the...

Adjust-a-bowl alone is worth it.Doc

Roller Bearing Installation Tool. Doc

Got out of the service in May of 65. Two months later a 'Nam buddy got out and called me. I went over and he had some hash. We took to heating a couple of table knives and using a soda bottle with the bottom removed to suck up the vapor. We ran out of hash so tried a nug. That was my first time...

When I use my Jar head with the Omni I can only count 4 seconds, first heat. It's a little close at the end of the bowl. I like the "M" to use with the Jarhead. I hate hunting for the air port. It's one reason I like the Omni. When useing the M I place my finger over the air port, and roll it...

I have a Jarhead, but what is the difference between a Jarhead and a Jarhead II? Am I behind the times? It's tricky cause the point between heating and combustion is on a knife edge. One half a second too long and smoking. Maybe I'm not holding my mouth right. I can feel the click then count...

I think I have a brown ring around my neck from where I keep my head. I kept wondering why my order wasn't showing up. I went on the DV site to find I hadn't finished my order. Called in and Matt found I had signed up twice. So don't vape and try to walk. I think I need to wash my neck. Doc

I always thought the answer to people not wearing seat-belts was "Velcro" seat covers and wear fuzzy clothes. Doc

I think it's in the bowl, that you are looking down into. Doc

Rince in coconut milk. If you look back in this thread Haze has recommended to rince the silicone parts in coconut milk. Ask Scott. Doc

I in no way condon doing this. Using distilled water clean qtip, upside-down, highest heat swab the bowl. I repeat, distilled water, highest heat setting, hold vape with oven facing down, carefully steam the bowl. Use a damp, (damp)qtip. Redampen as needed. Do not use tap water, (chlorine)...

The screen that is flat will be bigger than a screen that is concave. I should have said a 25.4mm stainless steel M8 bolt. If it falls out turn it over in the tip, concave down. Set it . A lot of people have a problem corralling the screens. The ti-tips have grooves where they "adjust-a-bowl"...

Ricardo, hit-em with a hammer. Screen on a steel truck bumper, or an anvil, or any large flat steel surface. smack it square-on with a smooth faced hammer. I do this every time I clean my vc. Unscrew the mouthpiece from the Omni and use the threaded end of the mp to set the screens. I have a 1"...

Wakeandvape, have you been watching "Laff-In" re-runs? :lol: Doc

I think it was Winegums, who explained to me that when wood is sanded the wood-grain sands unevenly. So the wongs, (wood on glass) are slightly out of round. They leak in a ground-glass joint. Just the nature of the beast. Want to seal up that leak? Hookahs have been around for hundreds of...

Want to increase the pull of your magnet? Your VapCap won't stand up? Stick it on a larger mass of metal. Put your little neo magnet on a steel truck bumper and see how strong it is. Don't forget your magnet, after you play with your VC on it. Now put the magnet on a tin box, (Altoids, Sucrets...