Search results

You can't hold the button for seconds on 7.4 you need to tap the button for perhaps half a second at a time. This gives the oil a chance to get close to the wire again works better for me then trying to just hold it down.

My original Persei tops are the same way. I actually hadn't tried it with my double tops since I'm worried about cooking another one, but I'd tried my "V1" Persei top out (the one that came in the kit w/double top & box advertised 6V) and it has no voltage dead zones that I recall seeing w/my...

Really happy with the service from both Vapexhale and Massdrop, I posted regarding a personal preference issue with the flared mouthpieces, and they made some of the (older?) "bubbler-style" sidecirc HT's available for the drop. I read that half an hour ago when I got home from work and...

So I am behind the curve in many ways.. I only got acquainted with the 7.4V KISS cart recently and have to say I love it, but as much as I like the Persei shorty the full size doesn't always fit my needs. Well, I gotta say, after parting with most of my Omicron collection, I really like this...

I haven't given it that much time yet, but honestly, I didn't notice much difference on the 3.7 rod compared to the CORE with the 74 white rod turned down to about 7 volts! I just swapped rods and have gone back to the -74 white rod for my daily driver 74. The -71 I find to be too hot, too...

I don't think any of your problems are super ignorant. You seem to have tried a lot of stuff and I feel really bad that you are still having problems after so much effort, because my Herc experience has been totally painless and I feel that everyone is entitled to the hassle free awesome vape...

I have 2 hercs and I still have love for the EO cart!! Just picked up a 5 pack of the 2.4Ω and am trying out the SS kit on the double top. Old school!! Good times!!!

@TommydCat have you ever checked the SR-74, no x, instructions? http://www.w9tech.com/instructions/ Notice that middle category each version of herc has its own instructions. I copied the picture I posted out of the official SR-74x instructions, but the SR-74 has a different rod placement. It...

No need to measure spacing. The entire white band should be showing with the 71 and 74x. Alpha Centauri, a binary star system, our closest neighbor. I wonder and hope if this could be some sort of magical high end combo of titanium wire and the FC2000-like porus dark grey ceramic wick used on...

Sounds like you have the coil saturated and oil on top of the coil so plenty in there to vape, you should be good to go if you are producing vapor and see bubbling. If you have fully charged batteries you should be getting good vapor with BHO concentrates in 3-5 seconds and seriously thick vapor...

Hard to say. 99% of the time I use the Herc, I use the Nibbler.

this is waaay easier. Tilt it about 60 or 70 degrees to uncover the hole and.. beauty. thanks for the pro tip!

Fill the water to in the UP logo then put it on . When you put it on either the water stays the same or gets pushed up with a clogged herc. When you take it off you need to have the Herc not clogged. If it's clogged when you pull the Nibbler off there will be a seal that makes a vacuum and...

The Core comes with a full-size Persei tube (the same battery tube that comes with a Persei). This is why you need a Garnish ring to have the Persei head sit flush on the tube. The "18350" Core tube uses an 18350 SS tube. The same piece that comes with an SS kit. So you don't need a garnish...

You forgot the Hercules oil cartridge and Flexo e-nail ;)

Without a receipt your best bet is going back to the store where you bought it and seeing if there's any records they have of your purchase. Unless you want to purchase the http://www.w9tech.com/persei-repair-warranty/

Hairdryer moves air WAY faster, someone was complaining about dust before- hairdyer is the worst thing for that. I use my gun for heatshrink so not all is lost. I do a lot of marine electrical work so I needed a good gun for the pre-heatshrinked adhesive lined terminals. Having multiple fan...

Very happy to be wrong about this. Now wishing I hadn't bought the real expensive variable temp heat gun recommended on here.

Nope but it was earlier in this thread so shouldn't be too hard to find. No idea what page number. I believe a member posted that G had recommended to not torch the chambers and the member had bought new ones to replace the ones he'd torched. Personally I used a small torch lighter on mine a...

You surmise based on Temperature but that is only one factor. The interaction of the gas you're burning with the metal in and of itself causes problems. Just as you should never heat Ti with propane you shouldn't heat stainless with butane.