Search results

Page 182 has visible photo's.

Yeah right around the gold plate on the back end, up towards the dial.

I haven't been following this thread much lately as my Hopper has been pissing me off with weird back end issues. Anyway just wanted to chime in with a recent "GOOD" hopper experience as they seem to be rare. I was having an issue were if I fully tightened my back end the unit would not turn on...

I spent some time with my square coil today today. Torch, pliers, patience and more patience. I manage to get my coil back to near perfection. Loaded some bowls and had a great session. First time used since July. Can’t wait for the micro dose pods.

@Summer I don't have a Z and I'm sure someone will chime in if I'm off base here but TCR 185 seems like a good starting point for these 510 attachments. Wattage will depend on manufacturer recommended settings and your personal draw speed. For Splinter Z id recommend: TCR 185 , TEMP 385-400F ...

@foggyent lowering the resistance should increase temp. My Wismec DNA200 runs cool on those profiles as well. My mod resistance is @ 0.004 Time for testing.

I like convection vapes, I have a few. All of them produce a nice coffee grind like ABV. Here's the ones that I find get darker ABV on lower settings: Grasshopper Fire Wood 4 Herbalizer New Vape Flowerpot MVT Splinter Stempod I don't have issues getting dark ABV in the square either, It just...

My units the same. 460 in order to get dark enough ABV for my liking. Otherwise I run my ABV through another vape to finish it.

Any word on when Vgoodiez or PV will be getting stock ? I still can’t figure out how to watch an IG live stream. :myday:

@TastyTicTac You could pop in a S&B dosing capsule along with a packed stem to dbl your session or you could pack your screen like this:

wanting Splinter Z :mmmm:

Mine came off on my first deep clean. I soaked the tray in some warm/hot ISO and it rubbed off when drying.

@Haze Vaporizers I see what your saying. When assembled the screen actually covers the OD of the airpath that's flaking off. This flaking still drives me a bit bananas but I'm OCD

I re-posted @O-G-Reg photos as imgur is no longer supported on FC. You can use https://postimg.cc Come to think of it, I think mine has also flaked off finish in my air paths. Here's a picture of mine. @Haze Vaporizers these photo's don't look like misconceptions? They look like finish...

Thanks for the replies ! @Vaporific @SmokeyTheBeard have you noticed any loss in overall performance ? Or just the annoyance of having to unscrew the back end until it reaches the magical position to where it wants to work. I just started using my GH again today since it arrived back from it's...

Has any experienced issues with their GH not turning on when the back end is "fully" tightened ? As soon as I fully tighten my backend it stops working, It needs about 1/2 turn ccw to start functioning again. Im baffled :shrug:

Here's a little friday evening milkshot. Hadn't used this piece in a while, was drawing too fast and ran out of air at the end, had to tap out early. This was a 0.06 of NL#5 @ 600f on the controller, cold start.

I’ve had that happen to two older MacBooks. Battery swells like a tennis ball pops the touch pad right out of the laptop

The tool is very handy. It is my preferred method The Tool is not a necessity. It can easily be done without the tool & without the painfull screen fiddling. There was a img tutorial posted a few times months back showing how to easily assemble without the tool. If I can find it I will post it...

Yes, performance is on point! I quite enjoy the wide range of temps as well. I can play in terpsville at 380f or move all the way on over to the face melting district of the 500's. I changed temp increments to move 10degrees at a time, life is good. Fingers crossed! This would make my...