Search results

But would that apply to shipments out of Philadelphia?

If I understand you correctly, you turned the unit on and initialized the unit at a (presumably) lower setting, waited a minute, then turned it to max. My suggestion was to set it to max first and then turn it on, i.e., the unit initializes set at max. When you subsequently turned the unit...

Re-writing firmware using a wireless connection can be risky, it's preferable if possible to use a wired connection because if the updating is disrupted in any way the firmware device can be borked and then you're SOL. Some boards use a second device to store the code as a backup in the event...

I brush clean mine after each use which removes most of the particle residue. After 3-4 uses there is enough particle build-up in the ELB pores to require an ISO bath; I use a 100ml flask. With 8 ELB's having soaked, there is still only a very small amount of particles at the bottom of the...

I don't mean to be sarcastic, but what reclaim? I don't have any to speak of from my ELB's.

Perhaps what may the most important point, is that VXL has a reputation for doing all it can to make things right. So you can feel safe about whatever you decide.

Heat-up speed is one of the EVO's better features. I can't recall any Fanatic mentioning 10 minutes, by far the comments have been positive over how fast it is ready. I turn mine on at 3, when it hits green I dial it back to 10:30-12 (depending), when it hits green again it's built thermal...

Check the retailers on this site, there are FC discounts and these outfits are authorized and dependable. I've gotten excellent service and good prices from puffitup.com. The Q is sold through many channels, but many are not authorized distributors. If you have a warranty problem, Arizer will...

If the unit has timed-out then the clock is reset by toggling the switch. And I'm saying that when you switch it on again, dial it to 3 and then dial back when green. Verify this works. If it does, your unit may need a firmware tweak. Send SM a PM about it and mention I suggested you do. Re...

From my research and experience I'd say that it is highly unlikely that it was the tab. Of course anything is possible I suppose, but it's much more likely that your experiencing cumulative effects of the dryness. I have to be careful with this all the time, because it can sneak up on me. And...

Turn it on set to 3 and when it goes green, then dial it down to your preferred temp around 12, which will probably take approx a half minute. This will actually bring your EVO up to thermal mass faster. Post back your results. It may be hotter at the top than the Cloud OG (I think I'll...

Well as it turns out, I'm doing the same thing - holding HT in one hand, EVO cupped from below in other hand. So contact comes from lifting EVO up to HT rather than the HT sitting on the EVO. I only got joint-lock once, and that was with using ice water, not a good idea! :doh: And, oh, btw I...

Would you please share what you are doing to avoid joint lock?

Welcome to FC! No need to replace screens unless damaged. Unless you grind too fine, the Cyclone screen needs cleaning very infrequently. The elbow screen's pores will get clogged, how often is a function of frequency of use and technique used. To clean I use a small corked lab flask filled...

Doubtful, at least not easily. The inside screen needs to be flattened. That makes it even larger. Unless you could crimp the flattened screen to make it smaller, this won't work. The original 2-cap method was using 2 ELB's caps, no flattening, just pressing one part of the way into the...

That's terrific. As new questions arise, don't hesitate to ask. And pls update us on your results. I offer this suggestion to anyone new to the Q: Read thru this entire thread. That's a PITA of course, took me about 2 months to wade through it all. But there is so much valuable info here...

Wow, and that's after this . . . Couple dozen EVO sessions in under 24 hours. That must be a record! :D

Looking for another punch to the face, I see. :cool:

I should have mentioned . . . when you stir, also clear out any herb sucked into the elbow screen. I prefer a slow steady draw to avoid this, sharp or hard pulls usually clog the screen. Also, the general consensus here is that when just starting out it's best to work with the stock Cyclone...

Well OK, I got EVOlved and this happened . . . First hit with EVO set at 10:30 and a .15g load, thick milk . . . Second hit, noticeably thinner. Took a third hit, got a small whisp of vapor, too little to photo. To my surprise, the ELB had been cached in 2 hits. And I don't pull hard...