Search results

I agree, MJ to me is like hallucinogenics in that there really is a quick rise and then a pleatu of diminishing return that you just can not seem to beat, it is steep also. Once you reach that point of max highness anything further consumption is pissing in the wind. Tolerance also builds...

I don't think I could allow my mates to preorder on my recommendation, fair warning to all... Or friendships could be lost! Haha.

Won't be disappointed, can use the solo for as long as you need to trawl through FC and decide on another vape you "need". Yet to see anyone be unhappy with the solos performance.

$160 and a decent vape that's well regarded as a durable and safe vape... Once again I have to cast my vote for first vape to the airizer solo.

Mmmm, wonder how a a magnet would go stuck to the side of the bong. That with a WonG VC would be dreammmmy!

Spot on. I struggled a bit at first, but it is not too bad with a little patience. I use a skewer stick snapped in half.

no word back about my order yet, soon I hope! Rumours of this maybe in the next couple months is exciting.

@VapCap Realistically what would be the shortest a TI with a WonG body could be? More of the same Tried mixing it up, full closed carb no condenser and mouth puffing like @natural farmer suggests. To be honest, I don't mind it. I always get throat irritation from multiple hits in a short...

I assume the profit margins on these things will be less than that with R&D and raw material cost.

Do not have a drilled cap anymore, cant remember the actual diameter, it was the smallest drill bit I had. I don't think I'd recommend drilling the cap, didn't make it drastically worse and drawing with a closed carb was much easier, but it didn't seem to really make it any better and loads...

Just have to keep reminding myself that this is someone else's company and ideas, I can either be on board or get the refund. As far as the customer service goes, I have personally boycotted business for less on that front, but obviously I want one of these much more than their productions.

Anyone tested something similar to glass flowers like in the accent? I know hear sinks in the HA work well for small bowls with huge extraction. Haven't used one, but from what I'm hearing about the apparent convection but the apparent conduction it reminds me of the HA oven. Could be something...

Looking like this might come off the line before Zion? I preordered one of these due to international shipping on Zion, good to see one is in the wild. Looks really good! @pakalolo you are a beta tester of sorts?

Yea it seems to me to be the closest thing to a combustion high with vaping I have experienced if ran hot, and the closest to my old main combustion methods. Amazing how good the flavour can be after a clean and keep at low heat too, probably the best low temp flavour out of any of my vapes...

I think finely ground, high temp with a mostly closed carb is understandable for combustion. I either heat low and open carb, or heat a bit higher if I want to hit it with a closed carb.

VC Gives wonderful high heat extraction. It's all in the genius design, heat high on the cap, low temp, heat low on the cap high temp. In my experience unless you are closing the carb the whole time, as long as you are not going lower than the cap with the flame, and don't heat past the click...

My thinking exactly, does not burn and you still follow the click, heating further down, for longer obviously isn't the most butane efficient way as you are wasting a lot of heat into the body, but seems to be the best way to see how far you can push the vapcap, will see how the caps hold up...

I see the carb as a compromise between a dense draw, and draw restriction (although that balance is done beautifully in the vapcap) If enough air could enter under the cap and through the bowl there would be no need for a carb in my mind. Also if you have some silicone whip I found snipping a...

And my attempt at what @natural farmer suggests. No condenser so can just use the carb instead of removing from mouth to clear the mouth and go again. Seems to work well! Still don't like the draw, will have to try the sand paper trick at some stage, anyone know which grit would be the best for...

Maybe I was wrong? I thought the new wood/TI had 5 small holes that you could play like a flute?