Search results

The last shot of your display shows to last official firmware. Did you try the "myevic" firmware? Main features that effect our needs are: -ohms lock works better. -manual ohms calibration in 1/100 of an ohm resolution. -option to turn off ohms checking -time out can go to 15 seconds instead...

I think I see the problem...:razz: Time to get your feet wet. I have come up with a way that helps make the coils. Take one of the spare ss wires I sent and install the way shown below. Now you need to make a jig. Take the top off a narrow type marker and cut two slits down the sides about...

Yes, @KeroZen is correct about it being cranked up. You will likely never see the high wattage do to limitations of battery output rating. The high demand is not being sustained for long and should not be that hard on the battery. Good point though about the battery possibly dropping too much...

I found higher TCRs give you a larger change to temperature per amount you the see on the display. I like it cause from beginning of session to the end is only one press of the button. The lower the value the less the scaling means in actual temperature change. If you look at it on a graph as...

I was looking at mugs and found there's such a huge variety. The SS or Aluminum mugs can get very pricey. The ceramic is cool but a bitch to drill the hole into. Plastic is the cheapest but not fancy which might actually be good stealth wise. What I'm thinking is to just make the unit on the...

In the menu under "interface", make sure the option "PPWR" is turned "OFF". Should have being off by default. That setting puts the set temp in the background and lets you vary the max power. No idea why one would like this but the option is there. Along with a ton of others.

First off, to complete the soft switch mechanism. I drilled a hole while the inner dowel was resting atop the tensile switch. Then, I drilled out the center doweling to be a couple mils bigger. Finally, I pushed another piece of wood (wooden QTip) through the hole and cut it flush. Hooray...

Try downloading from link below. Newest "myevic" firmware. (Dec19,2016) And I took out the non-relevant parts and left the Operation Instructions here. Maybe you will have better luck with this route. And although not for everyone. Here is the NFE software application. More for perks who want...

No display? 5 repetitive clicks do nothing? Sucks, should have warranty.

Man, wow. :razz:. Cuboid dead is a rare thing. Even when things go south updating the firmware, it has a recovery method. Pressing and holding the + and fire buttons. Now the firmware loader(s) should be able to see it on the PC. OR if in really deep dodo (no display at all): I think you are...

You must have a Pharmacy, no? 99.7% ISO is available from your pharmacist. The cheap 70% rubbing Alcohol is on the shelf and the "good" stuff is either behind the counter OR they can order it for you. Just say you clean electronics and must be pure with no residue.

Highly recommend you look through the menu instructions as has lots of features. But once all set up, you will love it. @natural farmer, so happy you're enjoying the Project so much. It does become a daily driver very quickly. And have never had a coil burn out on one yet. At least, that I've...

Grizzly, welcome to the land of choices. It's completely "open source" and I try to stick with materials which are readily available and provide links to sources. The problem is in acquiring all the bits and pieces for them, you end up having enough to make 10. I do my best to accommodate...

Glad your lovin it. Don't throw out your ripped sleeve. It can be repaired. Get some Eraser repair in a tube: Clean the pieces to be adhered together. Use a toothpick and apply fresh gasket maker on the rip. Once in place and looking correct, no longer touch for a few hours. Best to do before...

If just using for three favorite temps then your found one way to do it. TCR- slop of temp vs ohm/temp curve. In real life this slop is not linear. SS316 can range from 80-120 and ecig users select depending on what their preferred temp is to match real life as best as possible. The SS316...

Endeavor Update!!! Still waiting on the FET switch to finalize this pup. Decided on a soft switch mechanism. A typical tactile switch mounted in a hole of wooden doweling. Another cap type piece which will also go through the hole from the other end. This will be the part which the VC will press...

Thanks for such great first impressions. It does do as advertised. Funny how your using the TCR to control temperature. The TCR is mainly to make a change of 10 degrees to be 10 degrees. It has more to do with amount of temperature difference the numbers mean. Although, it also changes the...

I'm using the "myevic" firmware. Since it's universal firmware for many models, it only shows a single cell but you can read each cells voltage separately. They were talking about fixing this but no biggy. To make a custom logo, it's just a 2 bit colour depth (black and white) bmp file 64 pixels...

I'll find out shortly regarding the Ti cap. Ordered a Woody for testing. It sucks up 1.5 amp idle, and 6 amps with the OG inserted. So, 18 watts and 72 watts respectfully. But keep in mind the 12 volt supply I choose, because I have stock, maxes out at 50 watts. In other words, once just over 4...

Got a new skin today for my Cuboid. Goes very well with the Eraser. $1.50 @ FT :tup: