Search results

A quick update to the VC O-Ring reducer upgrade. In evaluating the mod, I ended up making a change that improves the rings staying in place. My Eraser is quite worn in and the ridges inside the bowl holder are worn down some. This has no effect on use with the standard stem but found the O-Rings...

Naw, it's hard in a large chunk but fragile in a thin layer. And messy as hell. It can take a really bright glow for a few seconds with no problem, from a cold start. The problem is the "from a cold start" part. When experimenting we tend to repeat pushing it's limits again right away without...

Does look like corn dog batter. :haw: Yes, the coil is in there. Just for fun, here's what the end result looked like before I pulled the plug on the idea. Too much power and took much too long to heat up. A way too much bulk.

You will find one contact point will be the top of the bolt supporting the VC. It is the positive side of voltage. I will cause some marks on the bottom of your cap. As does the coil when it touches the coils, but not as bad. What I did, was apply a very small dab of JB-Weld, maybe 1/2 a drop...

I will have enough Erasers within a week to fill the current list. Can't guarantee getting it within a month though.. PM me to get on the list. So for you VC lovers, a couple #110 O-rings will turn your Conduction VC into a Convection VC. Works Awesome!!! I'll be including a couple of these...

I am not in this for building up a business. It's a hobby and keeps me busy doing what I like best. I also have a full time career so finding a lot of time is not easy. Quite happy selling low quantities and staying within an enjoyable comfort zone. For the few that stumble upon my threads are...

Below is a cut/paste of the FAQ document so far. You can access the live version here. Let me know what should be added or changed. @fluffhead has editing privileges and will also be contributing to the information. Oh, @natural farmer, You made me break down and ordered that DNA75 for my ecig...

I don't know. I'd assume so, but accessing and navigating will be via that small display. I briefly looked at the PC software a couple years back and it sure looked like it had many bells and whistles but did not pay a lot of attention.

Nice looking unit. No TCR support but supports EScribe software for setting it up. No experience with this so it's unknown waters. Wish the DNA chipsets would come with a larger display. Has also been the hold back for me. I might try this one out for my ecig habit though as does look very...

That was my understanding too. The Arctic Fox was a branch off the myevic early on which went into the Russian programmers realm. Both are equally confusing for the newbie. And now having to pick even the open sources firmware to run your device... The Arctic Fox claims it can make it perform...

You made me do some digging but found it. Here is a pic of the original phase 1 charger.

It's the amps rating. Most adapters have very thin wire or that curly cord type stuff. These are designed for low current phone charging and such. We need to have 6-7 amps flowing. If you look closely at the picture I posted, you'll see the cord is more like lamp cord. In some cars the actual...

The stage 1 charger is for 3.2 volts batteries and stage 2 is the more conventional 4.2 (3.7) volt batteries. This information should be on the charger label. The mAh is the charging rate and the higher the faster.

All electrical options remain intact. The DC plug which will be pressure mounted into the side of jar can be pushed back into the jar and plugged into the battery pack. Batteries will need to be charged with an external charger and protected cells recommended as there is no built in protection...

Funny about that. I ventured out to the shed the other day intending to cut some pipe for making Erasers and ended up making a VC stem instead. Just turned a piece of Poplar doweling, stained and a coat of lacquer. After a night using it with the beta heater (gotta think of a name), and...

I believe I've got everything needed on order to make a few of these up. The 1st run production will consist of 15 units with the following changes. The search for a mug that was cost efficient and easily replaceable while maintaining a DIY concept, ended up an impossible task. I like avoiding...

Good eye. Yeah, been playing some. It's .3X.8mm flat SS. Works OK but the gauge is over the AWG 22 which I've being using. So to maintain around the same ohms, it ends up much shorter. Translates to it working harder and glows more visibly to maintain the temperature which is easily achieved by...

Patiently awaiting the 510 stems. I hope to start rolling some out through January. The glass gets very warm but not such it will cause instant burn. Mind you, I wouldn't hold it long enough to find out. The bowl holds about the same in volume as the Eraser but is longer and narrower. No cold...

I too, really dislike ordering from China because of world economics. However, can't beat the pricing and I'm a cheap ass. Our government makes it hard because of shipping charges whereas the China government subsidizes product exporting shipping costs. Which is the reason for all the free...

I started using Amazon for the nuts, bolts and washers. Still comes from China I think, but seems faster than Ali. Around 3 weeks..?