Search results

I have a VC on order as well. Experiments will begin next week. Being thinking about this and the key might be that in the video, he is using Kanthal. Kanthal can be shorted while coiling so must build up a layer of insulating oxide. I do know you can not do this with all element types. Anyway...

Did you try the Cuboid in bypass or power modes? Sounds like a possible problem Houston... Man, looks like I'm going to have to get a VC if going to proceed with confidence. :\

Hmmm, you make a good point about shorting the coil. I too was skeptical until @natural farmer passed this video on for my viewing pleasure. I am now assuming that the cap is electrically insulated somehow...? Perhaps has a coating on it.? I don't know but this video seems to indicate there is...

Hey guys. First off, huge thanks to @natural farmer who made me aware of the need for this type of device. It seemed to be a natural offspring for the methodology used in the Project Vape device, and proves to indeed be a shoe in, as takes basically the same base hardware configured a bit...

Well, here we go once again changing things. :uhh: In playing with the coil for the VapCap, I discovered that the coil got hot more uniformly with that type of build. So I got back to experimenting some. What I have come up with might please the folks having trouble with the V build. Let's call...

Perfect! Thanks @Alan. Makes a lot of sense and have rubber tubing on hand. :clap::tup:

I think this is more what your after NF. Now we're talking serious heat. Takes full power from the Cuboid to drive it. Which is 93 watts for this build. .9 ohm SS 304 22 AWG. Would prefer 20 AWG but this is what I had on hand for this mock up build.

Not right now as I have Erasers ready to go. As for the VapCap, I'll use the PM to give you an idea.....:sherlock::tup:

Sure can. Your in!

Yes, yes and drilling 3 holes equally spaced around the tube. 1.5mm holes.

So I received the 15ea glass male and female joints today. Made up a couple units which went well. Just waiting on the 510 stems to size up the ID on the cut male sections. As is, it's tight for most 510 tips but I know they are not all created the same so will wait for the designated stems to...

The Eraser will adapt to your favorite stem type. The stock and Solo stems are close in size and the Nano stem is a little narrower. If you use the stock or Solo stems, the Eraser will stretch out some over time and will no longer fit the Nano tight. If you plan to use Nano stems, do so from the...

@E0x, thanks for the suggestion and I see where your coming from, however, the support of the unit is in the O ring connection on the bottom. If dropped, I would think that is where the pressure point is on the glass, and that's where it will likely snap. A sleeve will have little protection...

Consider a reservation made my good man. The EVics firmware kicks it into power mode when the temperature or resistance doesn't raise as fast as it's expecting it to when X amount of time goes by. With the single cell units like the mini, it's a sign of weak/old battery or watts set too low...

Hey FC Project team. Decided to make a few of the Glass version Projects up. Ordered 15 of everything I should need. Still have a couple Erasers left and planning to keep making them as well. I have to admit that I have some reservations about a totally glass vape because of the frailness...

Today's mishap has turned into a blessing! The connector/bowl portion of the stem survived the fall. So I cut and bored it to fit a standard 510 drip tip. The selection of these mouth pieces is limitless. This also makes the insertion of the screen away simpler as well. Which was a concern for...

The new units are a tight fit on the base. Wetting the O rings to re-insert helps a lot. .48 ohms sounds a little light. Ensure the top loop of element isn't touching at the cross over point as it starts its way back down. This will effect units stability. Found this in my glass arsenal. It...

Howdy guys. Couple of updates. I have for a few Eraser version units made and ready to be adopted. If you prefers wood, let me know and I can make they per request basis. Currently testing a glass version. Thanks goes out to @mistvaporizer for the 14/23 female tube. I found drilling the...

The RX200S is now supported as well!! :clap:

That is fantastic @funkyjunky!!! Answers the mystery of how the tubo evic mod has the correct numbers showing in the video that @ZC mentioned. I tried the NFirmware editor and looks pretty slick. Unfortunately it couldn't communicate with either my evics. Some error regarding DCOM or something...