Search results

This custom carbless 18mm stem is gone to its new owner. I used western maple crotch wood and birch burl with rings of B20 and copper to make it. I had to grind a new lathe tool to cut the copper and bronze since it was proving difficult for my pinpoint tool. It fought me the whole way but was...

Two vapcaps tips are definitely better than one, you'll save your o-rings from excessive wear due to swapping so often.

The hole is to clear the vapcap and allow air into the vapour mix. There's two bi metal discs in the cap rather than relying on just one. Usually there's two clicks that come from the cap on heating and cooling. The ergonomics of the XL size stems work better for my big hands, though I could...

I don't doubt this at all, Cedar is low density and would act like a sponge for moisture. The denser exotic woods shouldn't dry things out as quickly. Yellow cedar makes me sneeze for hours if my dad does some cutting with it in the shop. Even being mildly allergic to it is not fun. On that...

If you have fine steel mesh or pipe screens you can cut and stack them to make a concentrate pad. I put a CCD on the top of the DIY pad to make it all neat and tidy. In my experience metal mesh works far better for concentrates over DGHF. Edit: When you're using the concentrates you only need a...

The o-rings can handle alcohol just fine, but I wouldn't go soaking the tip over night in it. I like using an Isopropanol soaked q-tip to scrub things out. I have to admit that that is a cool design. I never considered doing a latching system to hold things closed since magnets were simple to...

To be fair I haven't even had a chance to list these yet, I've been unable to make stems for quite sometime so my store is empty, and George puts on quite an attractive Black Friday deal. A Ti Nonavong is an excellent choice :nod: There's a whole classifieds area for posting your gently loved...

The stems are for Vapcaps and I've done nothing outside of the rules for those with commercial interest. There are plenty of accessory makers and manufactures that post in this thread and in the forum abroad. I'm sure that I would have been stopped long ago by the mods, (which are very active)...

Dat flavour tho.... Try a dry rip sometime, they aren't that harsh at all. They only down side is the glass can begin to warm up and lose its cooling ability with back to back heat cycles.

I'm sure they'll take care of you, I can only imagine how busy they are with all traffic from black friday. If they don't get back by the end of the week I would check in again.

I should have more up this week as I'm getting back to my lathing. These two 14mm stems I finished up this afternoon, Black walnut, Copper and Maple on the left and Cherry on the right.

Hey guys, Regular size cases are available now. More Maple and Cherry cases will be ready soon. https://www.etsy.com/listing/561510598/vapcap-case-regular-size-spalted-maple https://www.etsy.com/listing/561507320/vapcap-case-regular-size-cherry

I'm not sure if you missed it but I just posted Cherry and Maple XL cases, and I also have a 15% off sale + free shipping over $50 going on until 12pm Monday. Some of the regular size cases will be going up tonight after I can get pictures of them. I was hoping to have more completed by now but...

No, these are the two bay version with one side for the Vapcap and the other for general storage. I made the three bay version as a one off prototype. I can make another upon request but I didn’t make any this time around.

IIRC, Dynavap uses bees wax to finish the stem which would be no worse than inhaling vapourized concentrates. I also use bees wax to finish my stems since it's food safe and emits very little odor.

The Ti is thicker than the SS CCD which would offset the density difference. I've never noticed a performance difference between the two material types.

I've seriously considered picking up a skelator to combine it with my ABV bins but one thing or another has come up just before I order one. It's still something I want to do, but for now I decided to keep my bins general purpose. If anyone wants a magnet and stem holder installed into one in...

Custom cases are definitely available upon request. There’s lots that can be done with them as far as customization, the design leaves a lot of freedom for change.

My sale has started and XL cases are now available in my store! I also put the first coat of finish on some of the smaller cases. I'm really digging the maple panels with spalting in them, I may have to find some more pieces like them.

The XL Size cases are up in my store now and my sale has started. Everything in store is 15% off and orders over $50 get free shipping. https://www.etsy.com/listing/574785241/vapcap-case-xl-size-spalted-maple https://www.etsy.com/listing/574789823/vapcap-case-xl-size-maple-and-cherry...