Search results

I can assure you those batteries are fine so much so you should sling me couple while your at it :-P But seriously they are good. R

The more I think about it the more I think your right it is just not practical to incorporate both MP and screen, I don't think my design offered any improvement in that regard. However I don't think this deducts from the brilliance of your idea/design in the slightest and I am seriously...

It is meant as a replacement for the standard cap setup to add a bit of length to keep lips and face away from the heat, and as a more open flow design with a screen instead of the UFO mouth piece, I just want the ability to swap out the screen with the UFO incorporated in the design. I guess...

I would be happy to help seeing as it was my idea pm me his contact details. I know I promised a picture and didn't deliver I will try and find 5 minuet after work to smash one out. I really don't think it would be too hard to include all you would have to do would be to make sure the nipple...

Oops there I go again jumping in when I'm not needed :-) I still think my idea about screwing all the way in to confirm a seal between battery and air flow is not the worst in the world R Edit: I actually did a test a while back blowing some ecig vapour the wrong way into Cera and could only...

I think by shifting he means not screwing back in on it's own by means of something in the thread to physically stop the core from screwing in further. I do NOT recommend this as I believe the act of screwing the core all the way in so the flat plate just above the male thread of the core...

I feel like the failures are like buying a new piece of hardware for my PC... if it lasts out a week or two you know ur sweet. I feel so bad for all you guys with issues, I'm sure things will get better and failures will get less frequent. I really hope it's soon cause I feel like a fairy dies...

I have to disagree, yes there have been quite a few people coming here with problems, even confirmed unit deaths but without counting I would say less than 20. With at least 250? Units in the wild. making less than 10 percent failure rate, yep probably higher than TET would like but with...

sorry to ask a stupid question of you sneaky but when you say push the button you are holding it down aren't you? Just want to eliminate one possible issue. You should see the coil start to glow dimly within no more than about 6 seconds

I quite like the nipple setup I don't find it restricts airflow too much it just needs to be longer to stop me burning my lips (I currently have about an inch of 1/2 in silicone tube stuck on the end) what I find restricts air flow and reduces vapour production is packing too tightly, I have no...

I like this idea a lot it should be long enough to keep any meaningful heat from reaching your lips, it would be cool if the original MP nipple would also fit where the screen goes for folks that like it's magical properties :-) R

It's official this "I don't know what it is. I think I know what it looks like. I don't really want to touch it or ask a question that might give an answer I am uncomfortable about" Train of thought actually saved me loosing my Cera when the police decided to raid my house, 5 cops walked past...

I just want to say I am still very happy with my LLC I took her camping over the weekend and she performed perfectly. I seem to have found the correct draw speed as my abv is now coming out a nice even brow tobacco colour instead of almost black (though this could easily be due to my buds being...

Hey Dreamer thanks for the kind thoughts, but I'm sure I will never see any of it again, it's ok I'm over it. Can't get too hung up on these things. On a nicer note my two spare bats arrived today in all done up in shrink wrap in a nice little plastic case even complete with Panasonic paperwork...

Well it's official the cops do NOT want to know what Cera is, I tested it out (unintentionally of course). I had just had a session on my back verandah, set it down on the table and started hanging some clothes out to dry when I heard someone open my gate. Turns out it was mr. police man 6 of...

I've been doing some looking around for a couple of spare batteries and found that orbtronic still has the -CH 2250mAh advertised on their site even let me add some to the cart, but 50 bucks postage for 40 bucks worth of product was just too much for me (they do have to get them to aus but...

a week ago or so I was fiddling with Ceras bits and pieces (ohh that sounds so naughty :-P ) and managed to drop the top cap with out MP from about two feet maybe 2'6" ish onto the tiles in my back room, and it felt like time had stopped. It took about 5 minuets to reach the floor and I couldn't...

Sorry beat you to that first I've had one down in Melbourne for a few Weeks now, been posting my findings since. Also I agree with OF I have not been able to combust, vaped very dark but deffo not burnt. How fine did you chop? Buchee said he managed it, but had almost powdered the load and...

I'm gonna ask a welder/fabricator friend of mine to try knock my something up like OFs idea but try a bit prettier I'm thinking SS lever of a ball valve (so it's got a rubber cover) hooked onto a pivot arm suspended from a hinge level with the switch. I want the lever to be flat against the body...

I also have a short vid of me emptying the bowl you think I should put that up too? the ABV is pretty dark but I swear not burned in the slightest (I did learn from buchee and didn't grind too fine)