Search results

Thanks for the feedback! I am now leaning towards getting the medium plate... To load my vapcap I use it like a straw and sometimes the smaller particles do go through the vapcaps screen. Ok I think I will get both fine and medium. :leaf:

I am going with pink which is my wife's color of choice :) Which plate do you prefer to use for grinding herb to put into the vapcap? I am still trying to make up my mind whether to go with the fine or medium plate.

Ready to pull the trigger on a BCG... For grinding herbs for use in a vapcap should I go with a Fine or a Medium plate?

Thanks! Vaping has become another hobby for me. :) I should have gotten at least another one of those smaller boxes... I went back to the Dollar Store and they are all gone. :( The ZDS induction heater fits on the small box if you put it on its side. When I find the smaller box I will build...

Thanks! I got a smaller box which I now use to house my vapcaps... I also added a sticker and a magnet to the IH. Below is how it looks now... Also shown are the two bongs I mostly use with the vapcaps nowadays. I have also been mostly using Ddavemods Water Wand V2s with Ti Tips... I prefer...

That's one nice canopy! My favorite canopy is this one with powered by Scorpion decals...

The variety of connectors on lipos are indeed a pain in the rear. What I did in my DIY is to build a squid type adapter cable with different connector types on one end so I can plug in any of my 3S lipo even if it has a different connector. The wires I used for this connector has silicone...

Sometimes I tend to do too much research... over analyze things... This is manifested in my selection process between these two models lol. I am almost sure either will give me the same flavor I seek. :) In any case I am looking forward to comparing the flavor from the FC-710 to my other bongs...

I store the product I buy (typically 3.5 grams per strain) in 125 ml mason jars with a 4 gram (small) 62% boveda per jar. I use a 4 piece grinder to grind the weed just before a vaping session. Storing, grinding, vaping, cleaning the bong with dish washing soap right after use has become some...

I was actually going to buy the newer model (Rattle Can) from PopularGlass (stevenmlz79) but my research, including this Rattle Can vs FC-710 thread from r/chinaglass, made me reconsider and get the FC-710.

I only have experience with Dynavap Vapcaps... The vapor, especially from the M, is relatively hot and me and my wife were getting throat irritation after a vaping session. What solved this issue for us is to pass this vapor through a water pipe / bong to cool it off. Others have also used a...

I am more into getting the most flavor out of herbs lately and based on what has been posted in this thread and elsewhere, the glass of choice for flavorful hits appear to be the diffusion pump. I was going to get either the Rattle Can or the FC-710 from Stevenlmz79 but this FC-710 from another...

The one on the right is basically the bigger brother to my 8" Straight Fab Egg with a 14" joint. I would recommend that one as it has the well regarded laser cut SOL Perc.

By no means perfect but this has become my favorite so far... Cools the vapor effectively and at the same time retains flavor very well... Straight Fab with SOL perc from CCG:

@Pipes I saw this Gens Ace 800mah 3S lipo at RotorQuest... It has 50mah lower capacity and 5C lower discharge than the Tattu 850mah 45C I linked to before which I am using in my DIY IH. It probably is smaller than the Tattu. The Gens Ace has no measurements on the website but you can call them...

Nice flight Pipes! You definitely get a rush flying these things! You are right about my flight over the Bluffs... It was early morning when I took that video with very few people around. Even at the time, I timed my flights so there will be no one or very few people around. Even at the time I...

I flew drones (FPV) a while back but found it boring compared to helis... I have a couple of helis, smallest have 360mm blades and the largest 700mm blades. A few pics... Here's an FPV Drone flight... circa 2013 when you could fly drones everywhere... At the time gimbals to cancel...

I fly RC helicopters and one source of my lipos is RotorQuest in Toronto. Here is the link to one of the lipos I am using on my DIY Induction Heater (850mah 3C Lipo) at RotorQuest...

I am finding that I much prefer not to play with the carb when using my Vapcaps... I might end up using the SS Tip on a ddavemods water wand. I have been using these water wands V2 (with Ti tips) and prefer them even compared to my OmniVong XL. I already modded my SS tip and filed notches...

Question for those who have been using the vapcap far longer than me... What exactly is the advantage to having (or not having) the condenser? Reason I ask is because I am now using the ddavemods water wand v2 stem (no condenser) and, especially when used with a bong, it appears I can get...