Search results

The PS Mini list is FULL. (20 units) Man, that was quick. Not taking more names as don't want to get too far ahead of myself. Still room on all other lists. ;) :science: The positives are already connected. The FET switches the ground side. You should be able to just use a wire and touch a...

Correct on all fronts.

PM guys. It's the only way I can keep track and confirm back that you have being added to the right list. :cool:

Hey guys, I've managed to get an order in for another 17 Portside enclosures. So I can get a list going for a batch 4. Lines are open.... I know I've had a few requests but please re-request as I never started a list for another batch. Batch 3 PSs should be ready in about 3 weeks. The Mini...

Could you take a couple pictures of the rear of the BMS and post them to me via a PM? I'm looking for cracked solder connections from battery holder posts to the board.

I have received similar reports. I think whats happening is when inserting and depending on insertion order, the BMS balance protection is tripping. Seems the charger resets this protection state. The only concerning information you have given is the failure 1/2 hour after the reset. This is new...

Your very welcome! It's designed for batteries. If batteries are not matched, make sure you charge to full before you put them in. Should work for a while, at least till the discharge plays out more on the weaker cell(s), causing the BMS to shut down. Yes, it can run on a proper 12 volt supply...

Try dipping using something non-metallic. PM me the results and we'll go from there.

Hey guy's, just letting everyone know that I have caught up on the JH and Skelly lists. :haw: So if you haven't gotten a notification and was on the list, please let me know. Going to start into the PS batch next. Which the list is full and no room for more. Starting new Skelly and JH lists...

Completely safe there. It only touches wood and glass. Work coil is outside the glass. :nod:

If just cleaned, I'd suspect it's just the moisture sizzling off. For the most part, it's just 12 volts floating around before firing it up. I've touched it all over even while firing and have never gotten zapped. I imagine if you touch around enough while firing, you'll find somewhere that will...

:goon: Not sure how practical this would really be as well as power issues from doubling or tripling the output. Would need to be a pretty big party if one can't wait for a single hole to become free from use. Am I invited? :brow:

Battery maintenance can be very complicated as many have different ideas and usually have merit. Using the battery till lower limit is good for first 1-2 charge cycles as these are the most important cycles as they set the batteries boundaries. Once these are history, than driving to dead is not...

I have enough enclosures to cover the 3rd batch. Going to finish up the Skeletor and JhII backlog before I make up the PSs. Everyone currently on my PS list is safe. :cool: I have done some poking around and have come up with a scheme to make a PSMini, and have stuff on order to make a sample...

Thanks for the catch, post edited. :tup:

Wow, that did make it quick. A postal wonder. So guys, the list for batch 3 Portsides is now full and the enclosure supplier has being restocking for over a month now. This means I cannot commit to anymore PSs currently but will post if things change. Will also be looking for a replacement...

The mouthpiece will come apart. It's a standard 510 tip and I added the shrink wrap to aid pulling out of the joint. Just be careful as glass will be glass. ISO or even soapy water and a Qtip will suffice. :science:

Did you try changing the TCR with extreme changes? Like 50 or so. Really sounds like the Mod thinks it's not TC material and assumes it's Kanthal. Keep in mind that lowering the TCR will cause you to go higher in temperature values to achieve vapor. You are trying to go low enough to stop the...

It's possible as never had anyone give feedback for that mod. You could try and play with the TCR value. You're right that the firmware can do this, as it's limits or tolerances are all set there.

@KeroZen, the collar is too wide to go through the hole. Was snipping it off and then started to just install flipped over so lip is towards the small washer. @luke00978 , only move a tid at a time, centering as best you can. You will likely overshoot a couple times and have mod say it's...