Search results

Sorry to go off topic but you might want to check out this thread: Evolv Cricket

I have access to all types of concentrates in a state legal market. I have not tried any types of dry concentrates, only badder, sauce, live resin (I think). I don't pay too much attention to what I'm buying as long as it's not dry sift or kief etc.. I use 428F for all concentrates. I take a...

I use 428F, which shows as "Wax Mode" on the display. I only vape concentrates with the Legacy Pro, using the concentrate pad. Works great for me. It does require a long slow draw (30 seconds or more) to get it going, but once it's up to temp it produces nice clouds without too much heat.

There have been two reports of successfully heating the DaniVape with induction heaters. It looks like the DaniVape oven is slightly wider than the Anvil oven, which may prevent it from fitting in some of the existing portable induction heaters on the market, but the iSpire Wand has a much wider...

I have used the Anvil with the YLL Induction Heater many times. I don't recall seeing that error message. I use power mode and I heat the Anvil for 15 second cycles (watching the timer in the display). After the Anvil clicks I heat for 2 more 15 second cycles followed by one 12 second cycle...

No, the Anvil will not fit in the glass part of the DV adapter. It fits perfectly within the silicone sleeve of the DV adapter, but without the glass part. I flattened an old basket screen and inserted it into the bottom of the silicone sleeve to stop the Avil from sitting too deep in the coil...

I found that heating for 30 flashes after the click works perfectly for me with the Wand. I use the button to turn the heater off and back on when the Anvil clicks, then I count the 30 flashes. The Wand takes longer than most of my other induction heaters with the Anvil. I feel like that is due...

I seem to recall reading page after page in this thread discussing which torch, which butane, what flame length, where to point the flame, how long to heat, how to refill, how to purge, and how to maintain various torches for the Anvil. If you've got your torch(es) dialed in for the Anvil that's...

Heat the pad before trying to apply concentrate. I run at 428 F and do a "dry" draw for about 30 seconds. Turn the unit off, apply the concentrate - hopefully it melts fully into the pad. If there's any left on top it will probably stick to the gold spacer disc when you close the unit. Almost...

I don't have the exact diameter of the Anvil's oven, but the Anvil will fit into an opening that is 13mm. EDIT: The YLL that I received has the hole in the case slightly askew from the heating coil, so the Anvil tends to "catch" a little when inserting/removing it from the heater. Otherwise...

You are probably having issues because the DV is sitting too deep in the coils. I found the same thing when I tried the DV insert with glass tube. The DV sat too deep, so the heat was being applied too far from the cap, and the cap didn't click before the load was overheated. Induction heating...

Sorry I worded that poorly. I should have said that I haven't seen any issues with battery longevity, not battery life. Battery life is commonly used to describe how long a battery will last on a given charge. I was referring to how long the battery will last in the unit before it fails to hold...

UFO, Black Shadow, YLL Induction Heater, iSpire Wand, and Hot Fire Pro (aka "Click and Go", "Cuboo", etc). The UFO, Black Shadow, and Hot Fire Pro all seem to use the same firmware and share the same algorithms (12 second timeout, 5 cycle cutoff, etc). I would consider these to be the same...

I was encouraged by reading John's reference to a custom induction heater for the Anvil. I've been using my Anvil with induction heaters exclusively for several months now. I have it dialed in on 5 different induction heaters, including the Wand. I get very even dark brown ABV on a single draw...

I used the Roffu for quite a while before I got the dosing caps. They keep everything cleaner to some extent. I only get a few bits of material left in the top of the capsule when I empty it. The mouthpiece and its filter still accumulate resin, but with less plant material in it. Overall it is...

I have not used the Fury or TM dosing capsules in the Roffu, but the POTV One and V3Pro dosing capsules both work great for me in the Roffu.

Has the "dark ring" issue been addressed? Out of the box, the common complaint regarding the OG is the uneven heating of the material, leading to a dark ring of material surrounded by lighter/greener material. I know that many people have worked around this issue with different stem setups...

Add the convenience and simplicity of the V3Pro dosing capsules and the Roffu becomes a good beginner's vape. I had to work a bit to get the Roffu dialed in without the dosing capsules. I combusted a few times. I swapped between the two bowls. I altered my draw techique. I finally got to where I...

I only use the Legacy Pro for concentrates, and I only use session mode, so I can't comment on using it for concentrates in on-demand mode. My "best practice" is to heat the concentrate pad before attempting to add the concentrate. I power it on, wait for it to reach temp, and give it about 50...

I always charge my V3 Pro battery internally. I use an auto switching timer. I routinely set the timer for 2 hours and 30 minutes so I don't leave things charging if I forget about them. I have never seen the V3Pro battery register anything but fully charged when I turn it on after charging for...