Search results

Thanks you saved me some time researching the warranty issue. I am going to purchase a replacement. I will keep the one I have as a spare. It works well using tape to hold it in place. In my case I believe it had something to do with heat softening the glue and the strength of the magnet...

Thanks for the response. I think it needs the magnetic force to hold the cap to the body. I don't know where I would insert paper. There is an internal piece of plastic? that is visible when you look at the cap from the bottom. The magnet was glued to the inside of this plastic. The magnet...

The upper assembly of one of my two Roffus came apart. Referring to the exploded view in the manual the upper assembly has five components. The Zirconia Mouthpiece, Silicone Part, Zirconia Cooling Airflow Box, Cooling Cap and the grommet Filter. I now have seven components. The Cooling Cap is...

I do a three minute session with my Roffu (1 ml bowl .05g?) I take as many hits as I can get in three minutes, 10 hits +/-. I take a slow hit to half fill my lungs followed by filling the rest of my lungs with air and continue until the session times out. As the session progresses the vapor...

I haven't smoked since I got my dry herb vaporizer (Roffu) a few months ago. I like the way I can control the high. Start with a pair of three minute sessions to get stoned. And then the next day a single session to get high. Followed the next day with a buzz and then the load is about spent...

And when I want to decrease the humidity I place an open jar with granular diatomaceous earth (Autozone Floor Dry) pre dried in the microwave.

That's what I use and it works great. I use this jar opener to remove the vacuum sealed lids from the mason jars. It has a wide contact area and works well except for the strongest vacuum seals and even then I can remove the lid without damaging it. It is not designed for this specific use...

Using my AMZN quality tape measure I measure the overall dimension to be a little over 7/8 inch. Rounding down to account for the screen I get 22.2 mm divided by two to get the used area I get 11.1 which compares favorably with your 12.6 mm without the screen. Using 10.8 mm ID and 11 mm...

I make that 0.97 ml not accounting for wall thickness so actual volume would be a little ( 5% or 10%% +/-) less. Using your (AMZN quality) digital calipers what is the dimension of the oven chamber? On first read I thought you had an amazing quality caliper! Capacities using volume units...

Just finished reading the whole thread and I am sure I didn't absorb everything. I am impressed with the product and the community. I big shout out to @OMD and his attention to detail and his diligence. I want to join the owners club. I have a little bit of time to decide on the options. I...

I use three minute session mode at 320°F/160°C. I take a puff every breath. Towards the end of the session is when I start to see the fog. And yes a sprinkle fill with no tamping results in a much lighter draw.

What am I missing? I set mine at 320°F/160°C. THC has a boiling point of 315°F/157°C. I get stoned. I tried higher temps but I got harsher vapor, a heavy fog and a lot less scent. After a few sessions at 320°F/160°C when the weed is almost spent I have upped the temp by a lot and did not...

Referring to the exploded view in the manual. The upper assembly consists of four parts and a filter. The Zirconia Mouthpiece followed by a Silicone Part, Zirconia Cooling Airflow Box and then the Cooling Cap in that order. I can separate it into two pieces by pulling them apart to access the...

Thanks to all. I will now refer to the ring as a grommet. It would be helpful if we had an exploded view with components identified with part numbers if they exist. Half the time I am not sure what screen posters are referring to. I had one of my Roffus with the grommet installed one way and...

There is a rubber ring (not an o-ring, it has grooves) with a plate filter mounted in the center. It is mounted in the mouth piece and positioned over the oven chamber. One side is flat and the other is tapered (convex). Which side goes up? The flat side or the taper? In other words does...

My apologies, I did try it before I posted. I have other things in my cart so it must be using them too. With the current code WONDER the total is about half what you get with code JINGLE. WONDER is for 10 % off the entire order. Code JINGLE gets me about 20 % off the entire order. I don't...

Two spares with the full kit none in the lite kit. Another reason to get the full kit. Those are the ones I am trying to measure. I haven't replaced one yet. I am using the chambers as removable dosing capsules which requires pre filling. When on the unit there doesn't seem to be an issue...

@LesPlenty I found some more. All food grade silicone from -22℉ (-30℃) to 392℉ (200℃) 7.5 mm x 4.5 mm x 1.5 mm :clap: 8.0 mm x 5.0 mm x 1.5 mm 8.5 mm x 5.5 mm x 1.5 mm 9.0 mm x 6.0 mm x 1.5 mm Would you still recommend the 7.5 mm x 4.5 mm x 1.5 mm? Also this from Google so I think the spec...

Two month delivery time shipped from China.:( Are they silicone? Do they have a temperature rating? What is an OG? Any thoughts on 8 mm OD x 4 mm ID x 2 mm? A little wider and slightly larger than the one you posted. Or 9 mm OD x 5 mm ID x 2 mm? Or 10 mm OD x 6 mm ID x 2 mm? Those three...

There is a round filter that floats in the center of the oven chamber. It appears to have an o'ring. I have not been able to find spare filters or spare o'rings. I want to be prepared if/when I eventually need a replacement. What size is the o'ring? My best guess is 8 mm ID and 10 mm OD...