Search results

You need to set the TCR value, I reread your previous post and you didn't mention it. I've been using TCR=275 with the Stempod factory clapton coils. I'm using 43 watts and 430F with a Modefined Lyra box mod.

The "Coil of the Month Club" coils arrived in the mail today. They are "Clapton XL" coils; 7 wraps of 3 strands 28g wire wrapped with 36 gauge wire. They are 316L SS and fully TC compatible. The included information states that the "Coil of the Month Club" will be free for three months for...

This "The Project"?

Not a lot. Same here, it's what's holding me back on the single wire coil builds.

Don't be intimidated, best as I can tell Joules Mode is a gimmick, it's just TC mode with a different name. Watts and Joules aren't equivalent units even thought the iPV D4 treats them that way. Here are the settings I found that work with my Splinter on the iPV D4, note that the settings are...

Okay, good to know, thanks for bringing it up. The meager instruction sheet for the mod lists the following protections: Low Voltage Protection Low Resistance Protection High Input Voltage Warning Output Short Circuit Protection Reverse Battery Protection Temperature Overheat Protection The...

What was said?

Bwahahaha :evil: Here's an odd one, a Pioneer4You iPV D4 box mod with a YiHi board. I found it in a clearance section and couldn't resist. Its TC mode is called "Joules Mode" even though you enter your pre-heat number in watts. Your pre-heat number is on top and you have to dig through the...

Here's what I'm using for the two non-DNA mods. What are you using for Coil Material in your EScribe profiles for the Splinter and StemPod? RBT Splinter Lyra - TCR=260; 31 watts; 355F Charon Mini - TCR=260; 33 watts; 360F StemPod - notch coils Lyra - TCR=285; 38 watts; 395F Charon Mini -...

Testing is ongoing. :) I just started using the Paranormal, I've been using the Smoant Charon Mini and the Modefined Lyra head to head for about two weeks and they're very nice mods that feel good in hand, both with excellent TC implementations. So the Paranormal is up against some heavy...

From the original StemPod instructions, settings for notch coils: TCR=285; 35-40 watts; temperature range 360-420 (varies by material density and load size)

Yeah, I like the fit the o-ring provides too and I prefer it. I have no direct experience with either board but I did research and consider buying the Vaporesso Polar, VooPoo Drag, and VooPoo Too. There appears to be some firmware problems with the Polar, this reviewer, who regularly tests TC...

Yes, my paranormal was delivered quickly. No problem with the vendor, Aspen Valley Vapes.

I highly recommend the Coil Master Coiling Kit V4, I paid $11 for mine. The kit only includes what's needed for forming the coils, no other tools come with it. I'm also using the following tools: small diagonal cutter flush/side cutter ceramic tweezers chain nose pliers Nice video, what box...

Yes, I agree, the Splinter does run cool, especially compared to the DVTG2. For me, the Splinter hits much better than the DVTG2.

Thanks, good information. Is the staggered coil a staggered clapton?

I'm new to coil building so keep that in mind while reading this post. I've been experimenting with pre-built coils and coils that I made for the StemPod. First I tried a pair of Geek Vape coils, staggered, fused clapton coils in SS316L. The six wrap coils heated properly but the air drawn...

Damn, very well said @HerbieVonVapster! ^^^ You've hit all of the high points. This is key for users that don't want to mess around with building coils. The lifetime of the original notch coils isn't horrible and I have no doubt that Dan will develop a coil with longer life. I like to tinker so...

Thank you @Summer, that was very considerate of you to write up the IG stream summaries. What's available in 14mm stems? I don't think I've seen one, never looked for one either. A question for the members following this thread. I'm starting to develop some obeservations from building a few...

Here are a pair of Geek Vape pre-built staggered, fused clapton coils in SS316L. The coils came with the wraps touching each other, I put them on a 3.5mm coil mandrel and separated the wraps to create spaced coils. I haven't used this set-up yet.