Search results

Sorry, that was a placeholder, site is still being worked on Correct, 24 mm base and about 65 mm tall. Never had any plans for a wall unit. I'm only gonna start selling/preselling once I have a consistent, reliable, high performance product. Every step of development has taken longer than I'd...

Been working on a full website and material for investors, check out this demo for concentrate, concentrate + low temp flower, then a high temp sesh for full extraction in 2 hits

Sup donkey, always bringing the great posts. airpath is currently top down through the body and enters the bottom chamber right next to the coils. There are a few issues with heat transfer the way we have it now so the next prototype will have a much thinner outer body and bottom up airflow with...

Quick demo, abv was after 3 more off camera hits. How do you guys feel about the assembly, load process, performance etc? First hit was 70 watts, then 77, then through water at I believe 80

Working on a full website, what would you guys like to see? I am thinking of a design similar to an apple product intro page but with interactive elements like the dynavap site. Would love feedback on what people feel is the best way to do the layout, what tabs to have, etc. Video demo of the...

Exploded assembly: Left to right: outer body, build deck partially screwed into base, airflow adjustment top cap/outer cooling chamber, midpiece/inner cooling chamber, 810 drip tip, herb pod On a rx200 On a coolfire IV

generally pretty low resistance (.1-.15 ohm) different coils/elements suit different set ups

I am referring to Vandy Vapes mesh for installing into the build deck of our prototype for testing purposes. No relation to RBT's mesh heater. I am open to any collaboration Ryan wants to provide, I am hoping to coexist with other creators rather than compete. If Ryan is open to incorporating...

We don't have the proto in hand just yet but this print is the exact same spec. will have to see how the body handles heat. the mouthpiece should never get uncomfortable or even very warm but the body will likely get very hot. air intake has been directed to cool the body during a draw and...

First Prototype is nearly finished!

I like to run mine with a 40 watt preamp and cycle the power button (to avoid the cut off timer) for 10-15 seconds after the oven reaches temp without hitting it. then Ill cycle the power button again and take a slowish hit that speeds up near the end. If everything is dialed in right you should...

dynavap fat mouthpiece on a regular 510 driptip seals to a 14mm female

settings vary from mod to mod but for wax id say high 400s to start all the way up to 600 to kill a load. for cleaning "dan's balls" (why not lol) of the hash abv see if it all comes off in an iso soak, run the oven in wattage to get the black to burn off as well. also here is the...

tcr with smok is less than optimal but ive had luck in default Ni if i dont get kicked out to wattage. the extra horsepower really helps, if nothing else gets a rig hit try a 50 watt hit with 10-15 sec preheat on the alien, whatever makes 50 watts 6.5-7 volts

thanks for the feedback! sounds like a dual mod and some TCR tweaks are what you need to get good performance, I and a few other redditors were able to get thick and full hits off small amounts of shatter, not sure if that could be the hash but the flavor sounds like a tcr issue. with a dual...

Gn was the only fc member on the first round of 15 units, haven't seen anyone write up a review yet

could be done on any cheap conduction oven portable yeah, but most of those cap at 430 F or so and I run my castle in relatively accurate tc in the 500s for rig style hits. also most of the ceramic oven pieces are session which could work if you have people in a circle passing it dilligently but...

Wuddup! Thanks for the info post, anyone looking for more info can come visit the Castle Cartridge thread in the DIY section (currently have a manufacturer account with FC so I need to keep any product talk on my threads). Thinking about doing a detailed video walkthrough of assembly and links...

First order shipment post: https://www.reddit.com/r/Waxpen/comments/6zvgio/round_1_of_the_castle_cartridge_ships_tomorrow_pm/?utm_content=title&utm_medium=user&utm_source=reddit&utm_name=frontpage cloud demo from a happy customer...

Hey guys sorry about the radio silence on this project, gatherIng feedback from the first round before I decide whether or not to do a round 2 seeing as I almost lost money on the first order. Give me a few and I'll update with everyone's questions