Search results

Tiny Might meets Jack Herer :luv::) https://ibb.co/ynZC0Fx

Grav stem, with glass filter/holes, and quart sleeves. Hydratube seals perfect with the silicone mouthpiece from the gravel stem. https://ibb.co/HTNyTVD That hits as hard as anyone needs, for sure.

Sounds possible, but pretty speculative. I guess I'm just not worried about it. A whiff of gasoline at the gas station sounds more harmful and I dont really worry about such things. Something for version 2 to improve as a selling point for some maybe.

"the only harmful material when burned is the solder stop mask located in the battery contact spring but is on the other compartiment." Edit: The bottom of the unit has not even got really warm or hot in my usage. Not even warm, although the wood will get warm, not hot. I suppose the some...

For sure. Air is dawn through the holes in the top, and directly under the coil. The coil is attached to electronics, but there is a gap between the coil and electronics. The way the air flows, not over any electronics, I haven't really given any more thought. For those concerned though, that's...

I have a unit from December and a unit from March. I cant figure out where any gap is on my units. I see what might be a gap or pinched oring or just a shadow hiding some of the oring in the pic above, in the upper right corner. But the seal and o-rings sit nicely on my units ...

If your careful with the quartz sleeves, they work okay. I ran an all glass rig last night. It's a difference in flavor for the better. Stems should be on the looser side. If you have a tight fit stem, you stand a good chance a breaking the quartz sleeze. I pulled out thr Herablizer to cheat on...

Cheap vodka. Works good enough with salt.

Breaks super easy. I broke it before I could even use it. I bought three though, so can try again. Wet or lube your stem before trying to insert in the heating chamber. Any side to side motion will break the glass.. .. basically.

Maker said wait 5 seconds after adjusting temp before hitting. Edit: The silicone cap that comes with Grav stem works as excellent 18 mil, maybe 14 mil too, male adapter. They look like this: https://ibb.co/vdc7wnV

I spoke with him at the end of last week. Recieved a second unit Monday, order #191, placed in January, for those waiting. I think this order had extra delays because I ordered a few things and there was some confusion we sorted out over email.

Enjoy your honeymoon. I've been on one since December and haven't looked for any return flight tickets :shrug:

Yes. Here is from maker guy: "Hi! About combustion, There might be one explanation and a way to prevent this from happening. if you had just upped the temp and immediately started without waiting for sometime for it to get to the new target temp it could happen in theory. As you know the...

I don't why it combusted. I've used that same rig a ton, even on higher settings. Surprised the hell out of me. Perhaps the cooling unit and the screen being as bit dirty contributed to the combusting. So far just a one off.... but shows it is possible with the tiny might

First combustion: https://ibb.co/d4zycjM Level 9. Pretty fine ground and dry herb, but was hanging out with a 62% bovida pack just a day to two ago. Not packed tight. But cooling unit was a bit dirty. Every time this happens with any vaporizer, I'm reminded how much I don't miss combusting....

Ten and a half, what a blast! One more toke, and make it last :)

I read a little bit. I do like the idea of a stainless steel grinder. Aluminum is just there, available, but it's not a great material for the purpose. Might be bad for you. That said, until SLX v 2.5 starts flaking it's a great go to. My only complaint is that sidewalls of the screen piece...

Ordered some, thanks, great find. Website said a lot were being purchased, lol.

Nice option. Maybe not necessary. But I like responsiveness. I would prefer all aluminum replaced by stainless steel.

Just so I can watch for it on mine, where are the wear points that the purple coating is coming from? The United machining with all magnets is on my short list now! Edit: emailed United Manufacturing. Response in minutes. He said he will have units, likely, by April. :) Doesnt do preorders...