Search results

I remember that too

I don't think you really understand my posts... flame size/position determines the appropriate draw rate needed to maintain desirable load temps. higher draw rate while maintaining load temp = "faster" vapor production. two sides of the same coin. I think of the difference between a little...

not knocking the vapman, I really like mine too, but when you factor in the time to heat up the vapman, lily ends up being quicker. crank up your flame and back away from the intake would be my suggestion for anyone not blown away by the vapor output. it increases airflow in addition to...

if you are taking forever to get vapor from lily then I must say I believe you are doing it wrong. one of the things I love the most about lily (and daisy) is how quickly I can pull a massive cloud. you can pretty much draw as hard as you want if you provide enough heat! you have to get...

yes, I believe so. flexicones are the only way to go IMO

I was curious so I clocked my heat up times to green: ~5:00 min for teflon, ~5:30 for glass. Faster than I expected. This is starting around 70*F, using the AC puck. I almost never use the battery these days, but I sometimes will switch over to battery after heating up with AC just to move...

amen. July pre-order checking in here. Not my first pre-order, and of course I have other options to tide me over. Obviously I want mine as soon as it's ready, but not at the expense of quality. It's going to have very stiff competition as soon as it pulls into my station. So my attitude is...

for sale is my Firefly along with an external battery charger. This unit worked great up until the point that all my batteries failed. which I'm pretty miffed about, so I've decided to let the FF go. I understand there is some variation in terms of performance with these units and this one...

for sale are these two custom glass stems for the Hammer vape. I'm also including the Hammer vape itself, which unfortunately does not work anymore thanks to a failed piezo unit. It worked great up until the point that it would no longer spark and ignite. I understand that the piezo element...

This thread baffles me sometimes because I get big vapor on the first draw, even with small loads and I always use the baskets. I've been through a few failed units and my rule of thumb is now "if I think my MV isn't working properly, I'm probably right". It should produce copious vapor and...

I want to share some very good news for MV owners located in the USA. I was having an issue with my TC MV, and I sent it in to our very own @stickstones for service. he did a full heater replacement and firmware update, and shipped my unit back in less than a week! how's that for a...

@subway13029 - if it is taking around a minute to get back up to temp between draws then your unit is definitely malfunctioning. My glass core unit takes 5-10 seconds to recover after a huge draw. Most draws only cause it to blink 2-3 times. Recovery time on my unit is negligible. I would...

EDITED.... nevermind, I misunderstood FWIW, I had a Crafty for about 8 months and recently sold it. It really worked great, but effect, taste, and efficiency were all inferior to the MV. And of course the Crafty/Mighty cooks the load constantly, you can't use the Crafty/Mighty without the...

I was an early bird IGG backer on the EVO. It is a fine device but it was retired by my miniVAPs. I also love the vapman. current rotation is miniVAP + vapman. go figure. I see both sides of the coin if your budget isn't big, all you need is vapman + daisy. I'm not sure that combo is...

I bought it back in December 2014, but it's only got 29 hours logged on it, so it's been pretty lightly used. Still using an old version of the firmware (v2.04), but I have never had any problem with it whatsoever so I never sent it in for an update. I get 3+ sessions out of a charge, and I...

miniVAP glass core hope this isn't too blunt but I have a crafty that only gets used when I'm out and about and an EVO that hardly gets used at all. Several other vapes have been given away or sold The MV delivers superior flavor and effect IMO. It also allows plug in use that doesn't...

I'm going to try the MV with tiny cut pieces when I get back from this trip. Sounds like it might just bridge the gap between ground and "whole" flower. the whole flower method does make for a more prolonged session. I think that's the trade off.

@MinnBobber - I hope you don't consider this a thread derailment but I know you have an MV, so I wanted to comment that I have started using unground/uncut nugs in both the tc and gc MV's, exclusively. I get like 3-5 incredibly tasty rips depending on strain, then use a pick to break up the...

Just checking in to report zero problems with the 2015 MV's. The glass unit seems to heat up considerably faster than the teflon one, which is curious. However they both work great as soon as the light goes solid the glass core works especially well with unground material, which is my...

by "vapor tools" I meant vaporizers. but I'm pretty sure you knew that either way, I think I see the problem here