Search results

hahaha, yeah...for me, obsidian is THE surface with SiC a close second. I know some love sapphire but too much $$ and too fragile for me, personally. All I want is a neutral taste from the surface and I find that they ceramics do well at that. Cheers and congrats.

I do the same and also do not use PBW on metal. Glass, ok. Metal...eh, nah.

If you want accurate measurements to the hundredths, get a scale that read to the thousands then discard the least significant digit. I do not weigh out loads anymore, really. I just use the NV Pax Loading Tool and a level scoop of fine ground is right at about .1 grams. I tend to run my FP...

Well, I kind of remember the very beginnings of this thread and my getting glass OG DV (of which I still have a few, yep) but only drop in every once in a while to see what's up. I mean, 2K pages, right? haha I might have taken the "woodie" outside and laid it on the ground and run over it a...

I have suggested in the past that there are a number of switching tech that are far more reliable than a mechanical clicker. For what it’s worth.

Indeed, and I do hope that this comes true. But hasn't this been said for the last four years?

IMO that's because its the dumbest design ever for an on/off switch on an electronic device and I can only attribute it to slavish devotion to making the damn thing look like a pen. This is a $300 vaporizer, not a 50 cent click-it Bic pen. The clip falls into that category for me also...

Just feeling a bit shot up by life these days, Bruce. LOL Just got life locked in on my six. haha

I do not know what they have improved exactly in the IO wrt to testability but in the OG GH fault isolation and testability apparently sucked balls because they often (well, often enough) shipped back units from RMA that still malfunctioned and did this serially in some cases. Also, cases of...

Haha. I’m sorry but I did get a chuckle from your post. May I assume you are not a serial RMA GH owner? Most I can remember reading on FC was 9 on the same unit but I do vaguely recollect reports of more.

Still are to the best of my knowledge. They are basically a very high end machine shop.

I see that @mr_cfromcali posted some pics. And, while he noted that the LED is visible directly above the insert, he did not mention the three or four cooling holes where the light shines out of the side. You can see this in his last picture. Like yourself, I just want to see if the device is...

So, is this an example perhaps of different units heating very differently (not all that uncommon in the OG GH, even after RMA) or just a difference between two vaporists habits and desires? Be interesting to see others come on and give us some insight into temps used to see if they vary quite...

While it may say that in the documentation, I have found slow draw to be best but certainly not 20 seconds. And many of us (incl me) are familiar with a 15 second draw from the MV1 which really does need it and buzzes to let you know when time is up. In my estimation, the draw required by a Go...

I too would enjoy a bit more light from the LEDs, but I'm sticking with CF for the unbreakable win! :-)

Ah, thank you...insofar as I went with carbon fiber insert and have a 15mm coil, this wasn't applicable to me so I wasn't cognizant of it. Again, thanks and cheers

Thin wall....thick wall....??? What is this, please. This is not an option as listed on your site so I'm baffled. By the by, I run a 15mm coil with a Ti tip and think its perfect. The heating rate and timing is very similar to my old Lucid and using a torch lighter and I do not find it too...

IMO, the main and most important factor to consider between the NV controller and Auber (and its not limited to only this binary choice) is the connector type and pin outs. This goes to ease of finding multiple sources for coils. The Auber, and a great many (most?) of other controllers, use a...

Bet you wanted that decimal place to be one digit to the left, yeah? :-)

How do we upload an image as an attachment vice third party hosting via a link? I only see the one button to "insert image" and I think that just hot links....no???