Search results

Getting close to a viable unit now, mate :tup: And none of it would have been possible without this thread :nod::clap::) @FlyHi I've got several pages of A4 covered in notes and sketches to help with this process of log construction. Nearly all of it taken from this thread. Pretty much...

Got the heater cover finished today which meant that all components were ready for final assembly into a working log. That washer down there came with the jack plug connector. I put it in the vice and squashed it to a better size. Not the most elegant example of craftmanship I know, but...

H FlyHi Great to hear that you're doin' the DIY jive :tup: (to the music of KC and the Sunshine Band according to @ubardog ):D Here's the wire I'm using. The site offers a range of diameters - I went for the 0.9mm. But I guess bloke will be along soon to advise you on that and also on the ss...

Yea, I'll certainly use the higher temp solder. Anything that adds to safety and durability has got to be better. Heater position is straightforward and single 9mm tube is likewise. Thanks on that :tup: I'm still scouring the internet for suitable ss tubing. Very little 9mm out there...

How about... Manfred Mann - Blinded by the Light. 1977. "I'll turn you on son, to something strong..." Or anything by ELO ?? A previous attempt to build a desktop vape about four years ago, sadly, did not end in success. The heat source on that project was a halogen bulb. However, it's an...

Thanks for the info, bloke :tup: A longer leg on one side for coiling around the resistor makes good sense. It does look bit short. Possibly more spacing between the coils too, to make it a bit thinner? Lucky I only bought 50cm of that solder and not a whole spool. Thanks for the link. I'll...

The new solder arrived so watched Tom PD's vid and a couple of others. Practiced on some spare wire first then soldered the extension wire to the resistor. Yet another new skill this project has taught me :):nod: It's not shown in the photo but there's now 7cm of wire on one side and...

Many thanks for the useful centering advice, bloke :tup: Also, glad I checked with you on the solder before using it. You saved me some wasted time there :nod:. Will put in an order for the higher temp stuff today.

Got 3 x 30cm lengths of oak from this site on ebay - enough for about nine stems. They do say "un-sanded" and they ain't joking :o My advice is don't handle them without gloves until you've given them a good sanding. Bought some of that silver plated copper wire that you mentioned in an...

Oak 12.5mm (1/2 inch) doweling rods arrived yesterday so I drilled out an 8cm length. Countersunk at one end by 1cm with the 8mm bit to hold a ss tip. Very difficult to centre and drill accurately down the middle - but if you photo it from the right angle you can almost disguise that ;)...

Well, after much strenuous testing:science::science:, here’s my review of the latest Misty log vape. Friday, January 11th - tracking info indicated immanent arrival of the new oak Misty. Pm’d Bloke: “…the runway’s clear and the landing lights are on” - and it’s been my daily driver since it...

This is a literally brilliant concept :tup: Follow the light ! Does it work OK with a dd stem ? Or is the bulb too bright ? I imagine it could dramatically illuminates a bubbler :cool:

Well, look what the postman brought me this morning :D A log builder's kit :tup: Drilled and undrilled blanks for me to mess about with, ss tubing (two different diameters), a variety of washers and cliprings and a complete heater cover :clap: It's yet another fine display of Bloke's...

The big event chez brainiac this week was the arrival on Wednesday of the drill press. Finished assembling and setting it up yesterday and.. switched it on today :D Had some pine handrail/mopstick ready cut into blanks so I got out the forstner bits and 'had a go' :uhoh: Took great care...

Walnut's a fine wood for a log :tup: Lovely looking unit :clap: Any problems doing the drilling? It's quite a hard wood.

@ubardog still working on an answer to your question.. Yep, Bloke's picture is closer to the real colour of the oak unit. Took it down the beach this afternoon for a glamour shot :) Cloudy day with flat light doesn't manage to convey the richness of the wood tone, tho. Clearly, I'll...

Here she is :D Came carefully wrapped in recycled packaging materials :tup: The oak Misty - and what a beauty :love:. Great work, Bloke. Real craftmanship :nod: Mahogany unit there too, keeping it company :) Plugged it in, selected a suitably epic strain (Skunk #1), and put it to the...

My faithful OG Firefly (and only portable) is more than 3.5 years old and needs gently easing off into retirement :myday: so this M2G option for those 'away missions' is looking very attractive :clap: * sigh*.. looks like my to-do list just got a bit longer :D.

Don't hold your breath @Megaton - it'll be a while yet. Still gathering parts, tools and knowledge :) Local Jewsons does 50mm 'mopstick' in pine, but.. ...still dithering about a drill press :hmm: Anyway, big news at Brainiac Towers - according to a tracking number - new oak Misty unit inbound...

Wongs are high on my to do list. But this is the bit that I find difficult: Misty took a tumble about a week ago. Got dropped and the heater cover came loose. The unit was still perfectly functional... but it did rattle :\ Bloke advised me on repairs so I got to work :o Removed the...